Pioneer VSX-1124-K Owner's Manual - Page 94

Select 'On Screen Display Setup' from the Other Setup menu.

Get Pioneer VSX-1124-K PDF manuals and user guides View all Pioneer VSX-1124-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

12 The System Setup and Other Setup menus Software Update messages Status messages FILE ERROR UPDATE ERROR 1 to UPDATE ERROR 7 Update via USB UE11 UE22 UE33 Descriptions Try disconnecting then reconnecting the USB device or storing the update file again. If the error still occurs, try using a different USB memory device. No update file was found on the USB memory device. Store the file in the USB memory device's root directory. Turn the receiver's power off, then turn it back on and try updating the software again. If this message flashes, updating has failed. Update via a USB memory device. Put the update file on a USB memory device and connect the device to the USB port. When the file is found, software updating starts automatically. Updating has failed. Use the same procedure to update the software again. ZONE Setup Switches the sub-zone setting. 1 Select 'ZONE Setup' from the Other Setup menu. 2 Select 'MAIN/HDZONE', then press ENTER. 3 Set the usage of the HDMI OUT 2 terminal. ! MAIN: Select this to output the same input source as in the main zone. After setting this to MAIN, exit the home menu, then press OUT P. and select the terminal for HDMI output (page 71). ! HDZONE: Use the HDMI output's multizone function (HDZONE) to output an input source different from the one in the main zone (page 72). 4 When you're finished, press RETURN. You will return to the Other Setup menu. ZONE 2 setup When making multi-zone connections using the AUDIO ZONE 2 OUT terminals and performing playback in Zone 2, you can set whether to adjust the Zone 2 volume on the receiver or to fix it to a specific volume (-40 dB Fixed or 0 dB Fixed). This is set to Variable upon shipment from the factory, allowing the volume to be adjusted on the receiver. If you would like to adjust the volume from the connected amplifier, make the setting below. ! This setting is not possible if multi-zone settings have been made using the speaker terminals and Speaker System is set to anything other than ZONE 2. In this case, adjust the volume for the sub zones on the receiver. ! -40 dB Fixed/0 dB Fixed - The Zone 2 volume level output from the receiver is fixed to the value set here. 4 When you're finished, press RETURN. You will return to the Other Setup menu. On Screen Display Setup When the receiver is operated, its status (the input name, listening mode, etc.) is displayed superimposed over the video output on the display. This status display can be turned off by switching this setting to OFF. The setting can be made for the main zone and HDZONE, respectively. ! Default: ON (both the main zone and HDZONE) 1 Select 'On Screen Display Setup' from the Other Setup menu. 2 Select and set the main zone or HDZONE for which you wish to change the setting. 3 Select the On Screen Display setting you want. 4 When you're finished, press RETURN. You will return to the Other Setup menu. Notes ! The on-screen display is only displayed for video output from the HDMI terminal. ! When the video input signal is a 3D signal, the on-screen display may not be displayed. ! The size of the characters displayed differs according to the output resolution. Play ZONE Setup Select the zone for playing the audio contents of devices in the home network when using in the DMR mode. ! For playable DLNA-compatible network devices, see page 56. 1 Select 'Play ZONE Setup' from the Other Setup menu. 2 Select the zone in which you want to play the audio contents. 3 When you're finished, press RETURN. You will return to the Other Setup menu. Note If another zone is on, it may not be possible to play the audio contents. In this case, turn the other zone off, then play the audio contents. CAUTION ! Note that when Volume Level is set to 0 dB Fixed, the audio output from the AUDIO ZONE 2 OUT terminals is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may be produced even when Volume Level is set to -40 dB Fixed. 1 Select 'ZONE Setup' from the Other Setup menu. 2 Select 'ZONE 2', then press ENTER. 3 Select the Volume Level setting you want. ! Variable (default) - The Zone 2 volume is adjusted from the receiver. 94

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
94
The System Setup and Other Setup menus
12
Software Update messages
Status messages
Descriptions
FILE ERROR
Try disconnecting then reconnecting the USB device or storing the update file again. If the error still
occurs, try using a different USB memory device.
No update file was found on the USB memory device. Store the file in the USB memory device’s root
directory.
UPDATE ERROR 1
to
UPDATE ERROR 7
Turn the receiver’s power off, then turn it back on and try updating the software again.
Update via USB
If this message flashes, updating has failed. Update via a USB memory device. Put the update file on a
USB memory device and connect the device to the USB port. When the file is found, software updating
starts automatically.
UE11
Updating has failed. Use the same procedure to update the software again.
UE22
UE33
ZONE Setup
Switches the sub-zone setting.
1
Select ‘ZONE Setup’ from the Other Setup menu.
2
Select ‘MAIN/HDZONE’, then press ENTER.
3
Set the usage of the HDMI OUT 2 terminal.
!
MAIN
: Select this to output the same input source as in the main zone.
After setting this to
MAIN
, exit the home menu, then press
OUT P.
and select the terminal for HDMI output
(
page 71
).
!
HDZONE
: Use the HDMI output’s multizone function (
HDZONE
) to output an input source different from the
one in the main zone (
page 72
).
4
When you’re finished, press RETURN.
You will return to the
Other Setup
menu.
ZONE 2 setup
When making multi-zone connections using the
AUDIO ZONE 2 OUT
terminals and performing playback in Zone
2, you can set whether to adjust the Zone 2 volume on the receiver or to fix it to a specific volume (
–40 dB Fixed
or
0 dB Fixed
). This is set to
Variable
upon shipment from the factory, allowing the volume to be adjusted on the
receiver. If you would like to adjust the volume from the connected amplifier, make the setting below.
!
This setting is not possible if multi-zone settings have been made using the speaker terminals and
Speaker System
is set to anything other than
ZONE 2
. In this case, adjust the volume for the sub zones on the
receiver.
CAUTION
!
Note that when
Volume Level
is set to
0 dB Fixed
, the audio output from the
AUDIO ZONE 2 OUT
terminals
is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may
be produced even when
Volume Level
is set to
–40 dB Fixed
.
1
Select ‘ZONE Setup’ from the Other Setup menu.
2
Select ‘ZONE 2’, then press ENTER.
3
Select the Volume Level setting you want.
!
Variable
(default) – The Zone 2 volume is adjusted from the receiver.
!
–40 dB Fixed
/
0 dB Fixed
– The Zone 2 volume level output from the receiver is fixed to the value set here.
4
When you’re finished, press RETURN.
You will return to the
Other Setup
menu.
On Screen Display Setup
When the receiver is operated, its status (the input name, listening mode, etc.) is displayed superimposed over
the video output on the display. This status display can be turned off by switching this setting to
OFF
. The setting
can be made for the main zone and HDZONE, respectively.
!
Default:
ON
(both the main zone and HDZONE)
1
Select ‘On Screen Display Setup’ from the Other Setup menu.
2
Select and set the main zone or HDZONE for which you wish to change the setting.
3
Select the On Screen Display setting you want.
4
When you’re finished, press RETURN.
You will return to the
Other Setup
menu.
Notes
!
The on-screen display is only displayed for video output from the HDMI terminal.
!
When the video input signal is a 3D signal, the on-screen display may not be displayed.
!
The size of the characters displayed differs according to the output resolution.
Play ZONE Setup
Select the zone for playing the audio contents of devices in the home network when using in the DMR mode.
!
For playable DLNA-compatible network devices, see
page 56
.
1
Select ‘Play ZONE Setup’ from the Other Setup menu.
2
Select the zone in which you want to play the audio contents.
3
When you’re finished, press RETURN.
You will return to the
Other Setup
menu.
Note
If another zone is on, it may not be possible to play the audio contents. In this case, turn the other zone off, then
play the audio contents.