Pioneer VSX-C302-S User Manual - Page 5

Quick start guide - video cable

Get Pioneer VSX-C302-S PDF manuals and user guides View all Pioneer VSX-C302-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

English Quick start guide 01 Chapter 1 Quick start guide Introduction This Quick start guide shows you how to connect your speakers, TV and DVD player to this receiver, and also takes you through switching on and playing a DVD disc. 1 Connect your speakers to the receiver, as shown in the diagram below. Prepare the speaker cable by stripping about 1 cm of the plastic shielding from each speaker wire. Easy Setup This section shows you how to connect your speakers, subwoofer, DVD player and TV to this receiver so you can start enjoying home cinema sound right away. Before you start, make sure everything you're connecting is switched off and unplugged. Connecting speakers This receiver has speaker terminals for front left and right speakers (L and R in the diagram), a center speaker (C) and two surround speakers (RS and LS). The minimum speaker configuration is just the front left/right speakers, but we recommend connecting all five if possible. Note that surround speakers should always be connected as a pair; do not connect just one surround speaker. All the speakers you use should have a nominal impedance between 6-16Ω. Connect the front speakers to the FRONT L/R terminals; the center speaker to the CENTER terminal; and the surround speakers to the SURROUND L/R terminals. Press on a tab to open a terminal; insert the exposed wire, then release the tab to secure. For correct sound it's important that the positive and negative terminals of the receiver and each speaker are matched. To help you do this, attach the supplied colored self-adhesive labels to one half of each speaker cable. 2 Connect a powered subwoofer to the SUBWOOFER OUT jack, as shown in the diagram below. Use a standard audio cable with RCA/phono plugs. VSX-C302 SPEAKERS FRONT R L CENTER SURROUND R L ANTENNA AM LOOP FMUNBAL75Ω DIGITAL IN SUB WOOFER OUT TV/SAT (DVD) OPT1 DVR/VCR OPT2 DVD (TV/SAT) COAX IN OUT CONTROL VIDEO IN IN IN L L OUT L R R R DVD TV/SAT DVR/VCR AUDIO TWO VOLTAGE SELECTORS MONITOR OUT 220 -230V 240V 110V 120-127V AC IN 110V 120 -127V 220 -230V 240V LINE LEVEL R L C RS LS SW 5 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Quick start guide
01
5
En
English
Chapter 1
Quick start guide
Introduction
This Quick start guide shows you how to connect your
speakers, TV and DVD player to this receiver, and also
takes you through switching on and playing a DVD disc.
Easy Setup
This section shows you how to connect your speakers,
subwoofer, DVD player and TV to this receiver so you can
start enjoying home cinema sound right away.
Before you start, make sure everything you’re connecting
is switched off and unplugged.
Connecting speakers
This receiver has speaker terminals for front left and right
speakers (
L
and
R
in the diagram), a center speaker (
C
)
and two surround speakers (
RS
and
LS
). The minimum
speaker configuration is just the front left/right speakers,
but we recommend connecting all five if possible. Note
that surround speakers should always be connected as a
pair; do not connect just one surround speaker. All the
speakers you use should have a nominal impedance
between 6–16
Ω
.
1
Connect your speakers to the receiver, as shown
in the diagram below.
Prepare the speaker cable by stripping about 1 cm of the
plastic shielding from each speaker wire.
Connect the front speakers to the
FRONT L/R
terminals;
the center speaker to the
CENTER
terminal; and the
surround speakers to the
SURROUND L/R
terminals.
Press on a tab to open a terminal; insert the exposed
wire, then release the tab to secure.
For correct sound it’s important that the positive and
negative terminals of the receiver and each speaker are
matched. To help you do this, attach the supplied colored
self-adhesive labels to one half of each speaker cable.
2
Connect a powered subwoofer to the
SUBWOOFER OUT jack, as shown in the diagram
below.
Use a standard audio cable with RCA/phono plugs.
COAX
CONTROL
AC IN
IN
L
R
DVD
MONITOR
OUT
FM UNBAL 75
Ω
AM LOOP
ANTENNA
IN
OUT
SUB
WOOFER
OUT
TV/SAT
(DVD)
OPT1
DVR/VCR
OPT2
DVD
(TV/SAT)
IN
VIDEO
AUDIO
L
R
TV/SAT
IN
DVR/VCR
OUT
L
R
DIGITAL IN
CENTER
L
R
L
R
FRONT
SURROUND
SPEAKERS
TWO
VOLTAGE
SELECTORS
110V
120 -127V
220 -230V
240V
110V
220 -230V
240V
120-127V
LINE LEVEL
VSX-C302
R
L
C
RS
LS
SW