Pioneer VSX-D812K Owner's Manual - Page 65

Additional information, Troubleshooting

Get Pioneer VSX-D812K PDF manuals and user guides View all Pioneer VSX-D812K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Additional information 10 Chapter 10: Additional information Troubleshooting Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. Problem The power does not turn on. Remedy • Connect the power plug to the wall outlet. • Disconnect the power plug from the outlet, and insert again. • Make sure there are no loose strands of speaker wire touching the rear panel. This could cause the receiver to shut off automatically. • If the STANDBY indicator blinks and the power shuts off automatically, take the unit to your nearest Pioneer authorized service center or your dealer for servicing. No sound is output when a function is selected. • Make sure the component is connected correctly (refer to Connecting up on page 15). • Press MUTE on the remote control to turn muting off. • Adjust the MASTER VOLUME. No image is output when a function is selected. • Make sure the component is connected correctly (refer to Connecting up on page 15). • Select the correct component (use the MULTI CONTROL buttons). Considerable noise in radio broadcasts. • Tune in the correct frequency. • Connect the antenna (refer to page 20). • Route any loose cables away from the antenna terminals and wires. • Fully extend the FM wire antenna, position for best reception, and secure to a wall. • Connect an outdoor FM antenna (refer to page 20). • Adjust the direction and position for best reception. • Connect an additional internal or external AM antenna (refer to page 20). • Turn off the equipment causing the noise or move it away from the receiver. • Place the antenna farther away from the equipment causing the noise. 65 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Additional information
10
65
En
Chapter 10:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie
in another component. Investigate the other components and electrical appliances being used.
If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest
Pioneer authorized service center or your dealer to carry out repair work.
Problem
Remedy
The power does not turn on.
• Connect the power plug to the wall outlet.
• Disconnect the power plug from the outlet, and insert again.
• Make sure there are no loose strands of speaker wire touching the
rear panel. This could cause the receiver to shut off
automatically.
• If the
STANDBY
indicator blinks and the power shuts off
automatically, take the unit to
your
nearest Pioneer authorized
service center or your dealer for servicing.
No sound is output when a
function is selected.
• Make sure the component is connected correctly (refer to
Con-
necting up
on page 15).
• Press
MUTE
on the remote control to turn muting off.
• Adjust the
MASTER VOLUME
.
No image is output when a
function is selected.
• Make sure the component is connected correctly (refer to
Con-
necting up
on page 15).
• Select the correct component (use the
MULTI CONTROL
buttons).
Considerable noise in radio
broadcasts.
• Tune in the correct frequency.
• Connect the antenna (refer to page 20).
• Route any loose cables away from the antenna terminals and
wires.
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall.
• Connect an outdoor FM antenna (refer to page 20).
• Adjust the direction and position for best reception.
• Connect an additional internal or external AM antenna (refer to
page 20).
• Turn off the equipment causing the noise or move it away from the
receiver.
• Place the antenna farther away from the equipment causing the
noise.