Pioneer VSX-D812K Owner's Manual - Page 66

Sb Ch Mode, Signal Select, Digital, Analog, Signal, Select, Fl Dimmer, Problem, Remedy

Get Pioneer VSX-D812K PDF manuals and user guides View all Pioneer VSX-D812K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

10 Additional information Problem Remedy Broadcast stations cannot be • Connect an outdoor antenna (refer to page 20). selected automatically. No sound from surround or center speakers. • Refer to Speaker setting on page 45 to check the speaker settings. • Refer to Manually calibrating your listening area (MCACC) on page 51 to check the speaker levels. • Connect the speakers properly (refer to page 21 or page 22). No sound from surround back speakers. • Refer to Surround back speaker setting on page 46 to check the surround back speaker settings. • Refer to Using the Surround Back Channel (SB CH) on page 40 to make sure the SB CH MODE and the sound mode are set for surround back sound. No sound from subwoofer. • Make sure the subwoofer is switched on. • If the subwoofer has a volume knob, make sure it's turned up. • Switch the Subwoofer setting on page 46 to YES or PLUS. • Switch the LFE attenuator setting on page 47 to 0 dB or 10 dB. • The Dolby Digital or DTS source you are listening to does not have an LFE channel. Noise during playback of a • Move the cassette deck further from your receiver, until the noise cassette deck. disappears. Sound is produced from other components, but not from LD or DVD player. • Set the SIGNAL SELECT to AUTO, DIGITAL or ANALOG according to the type of connections made. (refer to page 37). • Set the digital input settings correctly (refer to page 50). • Make digital connections (refer to page 16) and set the SIGNAL SELECT to DIGITAL (refer to page 37). • Refer to the instruction manual supplied with the DVD player. No sound is output or a noise • Set the digital volume level of the player to full, or to the neutral is output when software with position. DTS is played back. When a search is performed • This is not a malfunction, but be sure to turn the volume down to by a DTS compatible CD prevent the output of loud noise from your speakers. player during playback, noise is output. Can't operate the remote control. • Replace the batteries (refer to page 6). • Operate within 23 feet ( 7 m), 30° of the remote sensor on the front panel (refer to page 7). • Remove the obstacle or operate from another position. • Avoid exposing the remote sensor on the front panel to direct light. The display is dark or off. • Press FL DIMMER on the remote control repeatedly to return to the default. 66 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Additional information
10
66
En
Broadcast stations cannot be
selected automatically.
• Connect an outdoor antenna (refer to page 20).
No sound from surround or
center speakers.
• Refer to
Speaker setting
on page 45 to check the speaker settings.
• Refer to
Manually calibrating your listening area (MCACC)
on
page 51 to check the speaker levels.
• Connect the speakers properly (refer to page 21 or page 22).
No sound from surround
back speakers.
• Refer to
Surround back speaker setting
on page 46 to check the sur-
round back speaker settings.
• Refer to
Using the Surround Back Channel (SB CH)
on page 40 to
make sure the
SB CH MODE
and the sound mode are set for sur-
round back sound.
No sound from subwoofer.
• Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• Switch the
Subwoofer setting
on page 46 to
YES
or
PLUS
.
• Switch the
LFE attenuator setting
on page 47 to
0 dB
or
10 dB
.
• The Dolby Digital or DTS source you are listening to does not have
an LFE channel.
Noise during playback of a
cassette deck.
• Move the cassette deck further from your receiver, until the noise
disappears.
Sound is produced from
other components, but not
from LD or DVD player.
• Set the
SIGNAL SELECT
to
AUTO
,
DIGITAL
or
ANALOG
accord-
ing to the type of connections made. (refer to page 37).
• Set the digital input settings correctly (refer to page 50).
• Make digital connections (refer to page 16) and set the
SIGNAL
SELECT
to
DIGITAL
(refer to page 37).
• Refer to the instruction manual supplied with the DVD player.
No sound is output or a noise
is output when software with
DTS is played back.
• Set the digital volume level of the player to full, or to the neutral
position.
When a search is performed
by a DTS compatible CD
player during playback, noise
is output.
• This is not a malfunction, but be sure to turn the volume down to
prevent the output of loud noise from your speakers.
Can’t operate the remote
control.
• Replace the batteries (refer to page 6).
• Operate within 23 feet ( 7 m), 30° of the remote sensor on the front
panel (refer to page 7).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off.
• Press
FL DIMMER
on the remote control repeatedly to return to
the default.
Problem
Remedy