ProForm 360 P Instruction Manual - Page 6

Assembly, Troubleshooting

Get ProForm 360 P PDF manuals and user guides View all ProForm 360 P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included hex keys and your own phillips screwdriver , wire cutters , needlenose pliers , and rubber mallet . For help identifying the assembly hardware, refer to the PART IDENTIFICATION CHART in the centre of this manual. Note: The assembly hardware and other small parts are packaged in separate part bags. Do not open the part bags until instructed to do so. 1. Make sure that the power cord is unplugged. With the help of a second person, carefully tip the treadmill onto its left side as shown. Partially fold the Frame (86) so that the treadmill will be more stable. Do not fully fold the treadmill until it is completely assembled. Open part bag A. Attach the two Base Pads (57) and two Base Endcaps (65) to the bottom of the Base (69) with four 1" Tek Screws (58). Attach a Wheel (66) to the Base with a Wheel Bolt (64) and a Nut (13). Note: It may be helpful to tap on the Base Endcaps with a rubber mallet as you insert the Base Endcaps. 1 58 65 86 64 57 58 66 13 69 58 65 57 58 2. Identify the Right and Left Uprights (29, 25); the Left Upright has two small holes in the indicated location. Make sure that there are two U-nuts (45) in the lower end of each Upright (see drawing 2a). Hold the Right Upright (29) near the Base (69), and orient the Right Upright so the indicated bracket is in the position shown. Straighten the Wire Harness (42), and feed it into the lower end of the Right Upright and out of the upper end. Make sure that no wires are pinched. Hand tighten two 3" Bolts (70) with Star Washers (63) into the bottom of the Base and the lower end of the Right Upright. With the help of a second person, tip the treadmill onto its other side. Attach the Left Upright (25) as described above. (Note: There is not a wire harness on the left side.) Attach the other Wheel (not shown) to the Base (69) as described in step 1. 2 69 63 70 42 6 Bracket 29 25 Holes 2a 29, 25 45 TROUBLESHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 9.) If an extension cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5 m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets. b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on position. c Tripped Reset d On Position PROBLEM: The power turns off during use SOLUTION: a. Check the circuit breaker located on the treadmill near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in. c. Remove the key from the console. Reinsert the key fully into the console. d. Make sure that the on/off switch is in the on position (see d. above). e. If the treadmill still will not run, please call our Customer Service Department. PROBLEM: The displays of the console do not function properly SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the four 3/4" Screws (2) a 2 from the Hood (1), and carefully pivot the Hood off. 1 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
15
ASSEMBLY
Assembly requires two persons.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex keys
and your own phillips screwdriver
,
wire cutters
, needlenose pliers
,
and rubber mallet
.
For help identifying the assembly hardware, refer to the PART IDENTIFICATION CHART in the centre of
this manual. Note: The assembly hardware and other small parts are packaged in separate part bags. Do
not open the part bags until instructed to do so.
1.
Make sure that the power cord is unplugged.
With the help of a second person, carefully tip the tread-
mill onto its left side as shown. Partially fold the Frame
(86) so that the treadmill will be more stable.
Do not fully
fold the treadmill until it is completely assembled.
Open part bag A.
Attach the two Base Pads (57) and
two Base Endcaps (65) to the bottom of the Base (69)
with four 1” Tek Screws (58). Attach a Wheel (66) to the
Base with a Wheel Bolt (64) and a Nut (13).
Note: It may be helpful to tap on the Base Endcaps with
a rubber mallet as you insert the Base Endcaps.
2.
Identify the Right and Left Uprights (29, 25); the Left
Upright has two small holes in the indicated location.
Make sure that there are two U-nuts (45) in the lower
end of each Upright (see drawing 2a).
Hold the Right Upright (29) near the Base (69), and
orient
the Right Upright so the indicated bracket is in the
position shown.
Straighten the Wire Harness (42), and
feed it into the lower end of the Right Upright and out of
the upper end.
Make sure that no wires are pinched.
Hand tighten two 3” Bolts (70) with Star Washers (63)
into the bottom of the Base and the lower end of the
Right Upright.
With the help of a second person, tip the treadmill onto
its other side. Attach the Left Upright (25) as described
above. (Note: There is not a wire harness on the left
side.) Attach the other Wheel (not shown) to the Base
(69) as described in step 1.
58
58
57
65
69
58
65
86
64
66
1
42
Holes
Bracket
29
69
25
2a
45
29, 25
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM:
The power does not turn on
SOLUTION:
a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 9.) If an exten-
sion cord is needed, use only a 3-conductor, 1 mm
2
(14-gauge) cord that is no longer than 1.5 m
(5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b.
After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c.
Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d.
Check the on/off switch located on the treadmill
near the power cord. The switch must be in the on
position.
PROBLEM:
The power turns off during use
SOLUTION:
a.
Check the circuit breaker located on the treadmill near the power cord (see c. above). If the cir-
cuit breaker has tripped, wait for five minutes and then press the switch back in.
b.
Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c.
Remove the key from the console. Reinsert the key fully into the console.
d.
Make sure that the on/off switch is in the on position (see d. above).
e. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM:
The displays of the console do not function properly
SOLUTION:
a.
Remove the key from the console and
UNPLUG THE
POWER CORD.
Remove the four 3/4” Screws (2)
from the Hood (1), and carefully pivot the Hood off.
2
1
a
6
70
63
2
Tripped
c
Reset
On
Position
d
13
57
58