ProForm 495 Pi Treadmill English Manual - Page 11

Caution - key

Get ProForm 495 Pi Treadmill PDF manuals and user guides View all ProForm 495 Pi Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

CONSOLE DIAGRAM Pulse Sensor Key Clip Note: If there is a thin sheet of plastic on the console, remove the plastic. CAUTION: Before operating the console, read the following precautions. • Do not stand on the walking belt when turning on the power. • Always wear the clip (see the drawing above) while operating the treadmill. • Adjust the speed in small increments to avoid sudden jumps in speed. • To reduce the possibility of electric shock, keep the console dry. Avoid spilling liquids on the console and place only a sealed water bottle in the accessory trays. STEP-BY-STEP CONSOLE OPERATION Before operating the console, make sure that the power cord is properly plugged in (see page 10). In addition, make sure that the reset/off circuit breaker, located on the treadmill frame near the power cord, is in the reset position. Reset Next, stand on the foot rails of the treadmill. Find the clip attached to the key (see the drawing above), and slide the clip onto the waistband of your clothes. Insert the key into the console. A tone will sound and the three displays will light. Test the clip by carefully taking a few steps backward until the key is pulled from the console. If the key is not pulled from the console, adjust the position of the clip. Follow the steps below to operate the console. 1 Insert the key into the console. When the key is inserted, a tone will sound and the three displays will light. 2 Press the Speed + button to start the walking belt. A moment after the button is pressed, the walking belt will begin to move. Hold the handrails and begin walking. As you exercise, change the speed of the walking belt as desired by pressing the Speed + and - buttons. Each time a button is pressed, the speed setting will change by 0.1 mph; if a button is held down, the speed setting will change in increments of 0.5 mph. To change the speed setting quickly, press the Quick Speed buttons. Note: The console can display speed and distance in either miles or kilometers (see SPEED DISPLAY on page 12). For simplicity, all instructions in this section refer to miles. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
11
STEP-BY-STEP CONSOLE OPERATION
Before operating the console, make sure that the
power cord is properly plugged in (see page 10).
In addition, make sure that
the reset/off circuit breaker,
located on the treadmill frame
near the power cord, is in the
reset position.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothes.
Insert the key into the console. A tone will sound and
the three displays will light.
Test the clip by carefully
taking a few steps backward until the key is pulled
from the console. If the key is not pulled from the
console, adjust the position of the clip.
Follow the steps below to operate the console.
Insert the key into the console.
When the key is inserted, a tone will sound and
the three displays will light.
Press the Speed + button to start the walking
belt.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
As you exercise, change the speed of the walking
belt as desired by pressing the Speed + and –
buttons. Each time a button is pressed, the speed
setting will change by 0.1 mph; if a button is held
down, the speed setting will change in increments
of 0.5 mph. To change the speed setting quickly,
press the Quick Speed buttons.
Note: The con-
sole can display speed and distance in either
miles or kilometers (see SPEED DISPLAY on
page 12). For simplicity, all instructions in this
section refer to miles.
2
1
CAUTION:
Before operating the
console, read the following precautions.
•
Do not stand on the walking belt when turn-
ing on the power.
•
Always wear the clip (see the drawing
above) while operating the treadmill.
•
Adjust the speed in small increments to
avoid sudden jumps in speed.
•
To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed
water bottle in the accessory trays.
Pulse Sensor
CONSOLE DIAGRAM
Note: If there is a thin sheet
of plastic on the console,
remove the plastic.
Key
Clip
Reset