ProForm 900 Cardiocross Trainer English Manual - Page 7

Pivot Axle 83 and to the two M8 Washers 55. Next

Get ProForm 900 Cardiocross Trainer PDF manuals and user guides View all ProForm 900 Cardiocross Trainer manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

6. While another person holds the Console (23) in the position shown, connect the wire harness on the 6 Console to the Extension Wire Harness (44). Insert the excess wire harness into the Upright Extension (73). Attach the Console (23) to the Upright Extension (73) with three M10 x 27mm Button Screws (67) and three M10 Split Washers (59). Be careful to avoid pinching the wire harnesses. Snap the bookrack onto the Console (23) in the indicated location. 23 67 59 67 Bookrack Wire Harness 44 67 59 73 7. Identify the Left Handlebar (6), which is marked with a 7 sticker. Insert the Left Handlebar into one of the Handlebar Legs (5); make sure that the Handlebar Leg is turned so the hexagonal holes are on the indicated side. Attach the Left Handlebar to the Handlebar Leg with two M8 x 45mm Button Bolts (50) and two M8 Nylon Locknuts (38). Make sure that the Nylon Locknuts are inside of the hexagonal holes. Do not fully tighten the Button Bolts yet. Attach the Right Handlebar (8) to the other Handlebar Leg (5) in the same way. Apply a generous amount of the included grease to the Pivot Axle (83) and to the two M8 Washers (55). Next, 6 8 Grease Tube 46 47 Grease 83 insert the Pivot Axle into the Upright (2) and center it. Reapply grease to both ends of the Pivot Axle. Slide a Handlebar Spacer (47) onto the short tube on each Handlebar (6, 8), and rotate the Handlebar 55 47 Arrow 84 46 56 38 5 2 Spacers so the small arrows are pointing toward the floor. Next, slide the Handlebars onto the Pivot Axle (83). Make sure that the Handlebars are on the correct sides. 50 Hexagonal Holes Tighten an M8 x 25mm Patch Screw (56) with an M8 5 Washer (55) and a Wave Washer (84) into each end of the Pivot Axle (83). Next, orient the two Handlebar Caps (46) as shown, and press the small tabs on the Handlebar Caps into the two Handlebar Spacers (47). 8. Identify the left Pedal Spring (11), which is marked with 8 a sticker. Attach the Left Pedal (13) to the left Pedal Spring with an M10 x 29mm Pedal Bolt (80), an M10 Washer (78), an M10 Split Washer (59), and a Pedal Knob (81) as shown. Note: The Left Pedal can be attached in any of five positions (see HOW TO ADJUST THE PEDALS AND THE UPRIGHT on page 9). Attach the Right Pedal (not shown) in the same way. Make sure that both Pedals are in the same position. 80 13 11 78 59 81 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
50
8
38
7
6.
While another person holds the Console (23) in the
position shown, connect the wire harness on the
Console to the Extension Wire Harness (44). Insert the
excess wire harness into the Upright Extension (73).
Attach the Console (23) to the Upright Extension (73)
with three M10 x 27mm Button Screws (67) and three
M10 Split Washers (59).
Be careful to avoid pinch-
ing the wire harnesses.
Snap the bookrack onto the Console (23) in the indicat-
ed location.
6
23
67
73
59
59
7.
Identify the Left Handlebar (6), which is marked with a
sticker. Insert the Left Handlebar into one of the
Handlebar Legs (5);
make sure that the Handlebar
Leg is turned so the hexagonal holes are on the
indicated side
. Attach the Left Handlebar to the
Handlebar Leg with two M8 x 45mm Button Bolts (50)
and two M8 Nylon Locknuts (38).
Make sure that the
Nylon Locknuts are inside of the hexagonal holes.
Do not fully tighten the Button Bolts yet.
Attach the Right Handlebar (8) to the other Handlebar
Leg (5) in the same way.
Apply a generous amount of the included grease to the
Pivot Axle (83) and to the two M8 Washers (55). Next,
insert the Pivot Axle into the Upright (2) and center it.
Reapply grease to both ends of the Pivot Axle.
Slide a Handlebar Spacer (47) onto the short tube on
each Handlebar (6, 8), and rotate the Handlebar
Spacers so the small arrows are pointing toward the
floor. Next, slide the Handlebars onto the Pivot Axle (83).
Make sure that the Handlebars are on the correct
sides.
Tighten an M8 x 25mm Patch Screw (56) with an M8
Washer (55) and a Wave Washer (84) into each end of
the Pivot Axle (83). Next, orient the two Handlebar Caps
(46) as shown, and press the small tabs on the
Handlebar Caps into the two Handlebar Spacers (47).
Grease
Tube
Grease
Arrow
7
44
Wire Harness
67
Bookrack
67
47
47
5
2
5
55
46
46
56
84
6
83
8
80
81
78
11
13
8.
Identify the left Pedal Spring (11), which is marked with
a sticker. Attach the Left Pedal (13) to the left Pedal
Spring with an M10 x 29mm Pedal Bolt (80), an M10
Washer (78), an M10 Split Washer (59), and a Pedal
Knob (81) as shown. Note: The Left Pedal can be
attached in any of five positions (see HOW TO ADJUST
THE PEDALS AND THE UPRIGHT on page 9).
Attach the Right Pedal (not shown) in the same way.
Make sure that both Pedals are in the same position.
Hexagonal
Holes
59