Pyle PKBRTP100.5 Instruction Manual - Page 2

3. Pull on the pressure relieving ring for a couple of seconds. If the keg was shaken in transit or warmed, it may contain excessive pressure which must be relieved before tapping. A hissing noise is expected. 4. Slowly turn the regulator knob in clockwise direction to 5 PSI, and stop for 2 seconds and turn o regulator. Wait for 2 mins, then pull on the pressure relieving ring for a couple of seconds. This is for adjusting pressure of keg beer. 5. Put a glass or pitcher under the faucet spout,with the faucet knob pulled forward (ON), slowly turn the regulator knob on in clockwise direction, until beer starts to ow out. Don't continue adding pressure,suggest tapping 5-8 PSI(max pressure 30PSI), so please stop turning the regulator knob when the pressure is enough to tap beer out with perfect foam. Too much pressure would cause over foam. When the beer stopped or ow slower, try turning the regulator knob on slowly, to get bigger pressure. 6. When you nish tapping, please turn regulator knob to OFF position. 7. If no beer ow out,then the C02 capsule needs to be replaced, unless no beer is rema ined. (Normally,16g capsule can tap 4-5 liters of beer). Caution: Removing a punctured capsule from regulator should be done slowly. Swish is expected if pressure remains. 8. Turn the regulator knob o and install a new capsule into the regulator by following above steps PART THREE: TROUBLE SHOOTING GUIDE 1. Faucet Leakage: Solution: Please screw out and remove the faucet and install again, make sure the faucet matches the connection of spear tightly. 2. SpearCross-bar Leakage: Solution: There is a nut under spear main body, tighten the nut to prevent leakage. 3. Too Much Foam: Solution: Flow-control block would help to reduce the speed of beer owing and reduce amount of foam. If there is too much pressure, please pull on the pressure relieving ring for a couple of seconds. When pressure within keg reach 30PSI, the pressure relieving ring would release C02 automatically to keep safe. 4. C02 Leakage: C02 capsule should be installed properly and tightly. In case there is C02 leakage, please observe the position of leakage and continue with the tightening process, but never screw out if gas remains. PART FOUR: WARNING 1. Keep away from children under 18. 2. Never point cylinder towards someone's face. 3. Do not heat over 140°F as rupture may occur! 4. Discontinue using of this equipment if unsolvable leakage or visible damage is found. 5. Capsule end become punctured when turned into regulator base. Unscrewing capsule before it's empty can result in loss of high pressure gas. Please remember, never unscrew the C02 capsule before gas used up, liquid C02 spray onto unprotected skin may cause freezing burns. 6. Exterior of capsule may become frozen when in use, this is normal. But don't touch with bare hands, your ngers could stick to the frozen surface and cause frostbite. 7. Please ship via land or sea shipment, never bring C02 capsule when you travel by air. Features • Complete Stainless Steel Mini Keg System • CO2 System Keeps Homebrew Fresh & Carbonated All Day • Solid Stainless Steel Construction Keep Beverage Colder Longer • Made of Food Grade S/S 304 Rust Proof Stainless Steel • With Neoprene Sleeve • CO2 Safety Pressure: 30 PSI PKBRTP50 64 Oz Stainless Steel Complete Set Dispenser & CO2 System Weight: 4.1 lbs. Dimesions: 13.4 x 7.5 x 6.9 inches PKBRTP100 128 Oz Stainless Steel Complete Set Dispenser & CO2 System Weight: 4.80 lbs. Dimesions: 19.5 x 7.5x 6.9 inches www.NutrichefKitchen.com www.NutrichefKitchen.com