Pyle PKBRTP110 Instruction Manual - Page 1

Pyle PKBRTP110 Manual

Get Pyle PKBRTP110 PDF manuals and user guides View all Pyle PKBRTP110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

PKBRTP60 - PKBRTP110 Homebrew Mini Keg Beer Dispenser 2L 4L 5L 10L Mini Keg with Spear Tap CO2 Regulator System. UNIT OPERATION INSTRUCTION 1 PART ONE: SPEAR ACCEMBLY 1. Please clean mini keg, cap, spear body, faucet and beer hose with warm water and mild soap before use. 2. Fill your mini keg at your favourite craft brewery, or with your own homebrew. 3. Cut beer hose according to keg height and insert into Spear, make sure hose can touch bottom of keg without overlong or over short. Remark: If hose is too short, beer would not be tapped completely. But if hose is too long, it may crimp inside the keg, also cause incomplete tapping. 4. Fit tube on to spear, and screw spear into mini keg. 3 2 4 5 9 8 11 6 7 10 5. Check whether the regulator knob is in OFF position. If not, please follow arrow mark instruction to turn the regulator knob counter clockwise to the OFF position. 1. Mini keg Growler 2L 4L 5L 10L. 2. Cap Spear Body 3. Gas In Connection Tube 4. Pressure Relieving Valve 30PSI. 5. Cross-bar 6. Regulator Base 7. 30 PSI Pressure Gauge 8. CO2 Regulator Knob 9. CO2 Regulator Aluminium Body 10. Black Plastic Tap Handle. 11. Chrome Plated Faucet Body www.NutriChefKitchen.com 6. Turn in a new 16g CO2 Capsule with thread type of 3/8-24UNF, turn clockwise rmly into the regulator base. NOTE: DON'T stop turning if you hear a slight gas leak swish, nish turning it in all the way it seal properly. PART TWO: TAPPING 1. Connect the regulator with capsule to the spear. 2. Install Faucet into Spear Body, make sure the connection is proper and tight. Remark: Improper combination would cause leakage of beer. 3. Pull on pressure relieving ring for a couple of seconds. If the keg was shaken in transit or warmed, it may contain excessive pressure which must be relieved before tapping. A hissing noise is expected. 4. Slowly turn the regulator knob in clockwise direction to 5 PSI, and stop for 2 seconds ad turn o regulator. Wait for 2 mins, then pull on the pressure relieving ring for a couple of seconds. This is for adjusting pressure of keg beer.

  • 1
  • 2
1
3
2
4
5
8
7
9
6
11
10
www.NutriChefKitchen.com
Homebrew Mini Keg Beer Dispenser
PKBRTP60 - PKBRTP110
2L 4L 5L 10L Mini Keg with Spear Tap CO2
Regulator System.
UNIT OPERATION INSTRUCTION
1. Mini keg Growler 2L 4L 5L 10L.
2. Cap Spear Body
3. Gas In Connection Tube
4. Pressure Relieving Valve 30PSI.
5. Cross-bar
6. Regulator Base
7. 30 PSI Pressure Gauge
8. CO2 Regulator Knob
9. CO2 Regulator Aluminium Body
10. Black Plastic Tap Handle.
11. Chrome Plated Faucet Body
PART ONE:
SPEAR ACCEMBLY
1. Please clean mini keg, cap, spear
body, faucet and beer hose with
warm water and mild soap before
use.
2. Fill your mini keg at your favourite
craft brewery, or with your own
homebrew.
3. Cut beer hose according to keg
height and insert into Spear, make
sure hose can touch bottom of keg without overlong
or over short.
Remark:
If hose is too short, beer would not be tapped
completely. But if hose is too long, it may crimp inside the
keg, also cause incomplete tapping.
4. Fit tube on to spear, and screw spear into mini keg.
5. Check whether the regulator knob is in OFF position.
If not, please follow arrow mark instruction to turn the
regulator knob counter clockwise to the OFF position.
6. Turn in a new 16g CO2 Capsule with thread type of
3/8-24UNF, turn clockwise firmly into the
regulator
base.
NOTE:
DON’T
stop turning if you hear a slight gas leak
swish, finish turning it in all the way it seal properly.
PART TWO:
TAPPING
1. Connect the regulator with capsule to the spear.
2. Install Faucet into Spear Body, make sure the
connection is proper and tight.
Remark:
Improper combination would cause leakage of
beer.
3. Pull on pressure relieving ring for a couple of seconds.
If the keg was shaken in transit or warmed, it may
contain excessive pressure which must be relieved
before tapping. A hissing noise is expected.
4. Slowly turn the regulator knob in clockwise direction
to 5 PSI, and stop for 2 seconds ad turn off regulator.
Wait for 2 mins, then pull on the pressure relieving ring
for a couple of seconds. This is for adjusting pressure of
keg beer.