Pyle PLA2480 PLA2480 Manual 1 - Page 4

features, controls, specifications - amp

Page 4 highlights

features and controls 2 ch amp PLA2180.PLA2280 PLA2180 PLA2280 power LED protection LED remote bass boost (PLA2180 without) high pass frequency control low pass frequency control high level inputs 6 low level inputs input level control crossover mode selector bass boost level speaker connections power fuse power terminals features and specifications 2 ch amp PLA2180.PLA2280 PLA2180 PLA2280 crossover mode selector when used with normal, full range systems, set this switch to "FULL." If you wish to use the internal crossover to power a driver of specific frequency range, use the "LOWPASS" or "HIGHPASS" settings. input level control use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o'clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point. output power @ 14.4v DC, 1KHz RMS Power @ 4 Ohms RMS Power @ 2 Ohms Maximum Power Output 2 channel amplifier 40 Watts x 2 70 Watts x 2 300 Watts x 2 frequency response 15 Hz-30 KHz 2 channel amplifier 75 Watts x 2 110 Watts x 2 500 Watts x 2 low pass frequency control when the crossover selector switch is in "low pass" mode, this control sets input impedance the upper frequency limit for audio program sent to the speakers. low level inputs 10K Ohms high pass frequency control when the crossover selector switch is in "high pass" mode, this control high level inputs 100 Ohms sets the lower frequency limit for audio program sent to the speakers. Remote Bass Boost Plug in the Remote Bass Boost Control wire in here. input sensitivity 7 low level inputs 250mV bass boost level control this control permits adjustment of the bass level up to an increase of approximately 18 dB. high level inputs 2.5V low level inputs this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker output leads to these input connectors. power LED this indicator is illuminated when power is applied. power supply voltage 14.4V DC Neg. Ground (10.5-16V) matching speaker impedance stereo mode 2-4 Ohms bridged mode 4-8 Ohms protection LED this indicator is illuminated when built-in protection circuitry is activated. maximum current draw 15A 20A power fuse the fuse protects the amplifier and your car's electrical system from short circuit conditions. power terminals use these connectors to deliver power, ground and remote turn-on control to the amplifier. dimensions (W x H x L) mm 276 x 69.5 x 209 inches 10.9 x 2.7 x 8.25 276 x 69.5 x 305 10.9 x 2.7 x 12 speaker connections these terminals are 14K gold plated to guarantee high conductivity and minimum signal loss.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

PLA2180
2 channel amplifier
frequency response
power supply voltage
output power @ 14.4v DC, 1KHz
RMS Power @ 4 Ohms
RMS Power @ 2 Ohms
Maximum Power Output
input sensitivity
low level inputs
high level inputs
40 Watts x 2
70 Watts x 2
300 Watts x 2
15 Hz-30 KHz
250mV
2.5V
14.4V DC Neg. Ground (10.5-16V)
6
7
maximum current draw
dimensions (W x H x L)
mm
inches
2-4 Ohms
15A
4-8 Ohms
input impedance
low level inputs
high level inputs
10K Ohms
100 Ohms
matching speaker impedance
stereo mode
bridged mode
features
and
controls
2
ch
amp
PLA2180.PLA2280
features
and
specifications
2
ch
amp
PLA2180.PLA2280
276 x 69.5 x 209
10.9 x 2.7 x 8.25
PLA2280
2 channel amplifier
75 Watts x 2
110 Watts x 2
500 Watts x 2
20A
276 x 69.5 x 305
10.9 x 2.7 x 12
speaker connections
power terminals
power fuse
crossover mode selector
input level control
low pass frequency control
high pass frequency control
Remote Bass Boost
bass boost level control
low level inputs
high level inputs
power LED
protection LED
power fuse
power terminals
speaker connections
when used with normal, full range systems, set this switch to
FULL.
If
you wish to use the internal crossover to power a driver of specific frequency
range, use the
LOWPASS
or
HIGHPASS
settings.
use this control to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o
clock position, increase
the amp level control until distortion begins to occur, and reduce slightly
from this point.
when the crossover selector switch is in
low pass
mode, this control sets
the upper frequency limit for audio program sent to the speakers.
when the crossover selector switch is in
high pass
mode, this control
sets the lower frequency limit for audio program sent to the speakers.
Plug in the Remote Bass Boost Control wire in here.
this control permits adjustment of the bass level up to an increase of
approximately 18 dB.
this amp features gold-plated RCA input jacks for high impedance input.
Use these with car stereo output which uses RCA-type connector cables.
if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
this indicator is illuminated when power is applied.
this indicator is illuminated when built-in protection circuitry is activated.
the fuse protects the amplifier and your car
s electrical system from short
circuit conditions.
use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
high level inputs
protection LED
power LED
crossover mode selector
input level control
bass boost level
low level inputs
low pass frequency control
high pass frequency control
remote bass boost
(PLA2180 without)
PLA2180
PLA2280