Pyle PTA22BT Instruction Manual - Page 4

NO POWER, NO SOUND, Feedback

Page 4 highlights

IMPORTANT Replacing a fuse This ampli er requires fuse with the proper rating for protection from power surges and short circuits. If the ampli er suddenly turns o or would not turn on, the fuse is properly blown. • Let the ampli er cool down and see if it starts again before you assume a fuse needs to be replaced. • Unplug the ampli er from the AC outlet. • Turn the fuse holder cap and pull out the cap. • Remove the old fuse and replace it with an identical one. CAUTION: Never use a fuse with a higher rating TROUBLESHOOTING NO POWER The fuse might be blown Check the ampli er's fuse and replace it if necessary. Sound source or speakers NO SOUND may not be connected properly Check all connections Master volume control Adjust the volume control may be set to a minimum to a higher setting The speaker's wire might have the wrong impedance Make sure that the speakers that you have connected to the amp are matching in impedance Turn the ampli er o and let it The ampli er is shutting cool, make sure that the down or powering o ampli er is properly ventilated, and then tum it back on Feedback Microphone and speakers are to close together Reposition the microphone and speakers 6 www.PyleUSA.com Features: • Hi-Powered Component Amplifier System • Compact Desktop Receiver System Design • Built-in Wireless BT Audio Streaming • Works with All of Today's Latest Wireless BT Devices • Smartphones, Tablets, Laptops, Computers, etc. • USB/SD/FM playing • Switchable Mic Pager and Mixing/Karaoke Modes • Page Mode: Allows Voice Transmission via Mic • Mix Mode: Allows Both, Voice & Music Transmission • RCA Audio Input (AUX 1, AUX 2, CD) • AUX (3.5mm) Input Connector Jack • (Connect Devices like Smartphones, Tablets, MP3 Players, etc.) • Treble, Bass, Balance, Master Volume Adjustable • Four Push Type Speaker L/R Terminals • Input Selector Switch • RCA Record Output • 1/4'' Headphone Output • 1/4" Mic Input Jack • Built-in Short Circuit and Power Surge Protection • Compatible with Audio/Computerized Devices • Rotary Master & Microphone Volume Controls • Front Facing Control Panel • LED Indicator Lights Wireless BT Connectivity: • Built-in Wireless BT Audio Receiver • Simple Pairing for Wireless Music Streaming • Works with All of Today's Latest Wireless BT Devices (Smartphones, Tablets, Laptops, computers, etc.) • Wireless BT Version: 5.0 • Wireless BT Network Name: 'PYLEUSA' • Wireless Range: Up to 40' ft. Technical Specs: • Power Output: 40 Watt x 2 (MAX) • 10% RMS at 4-Ohm Impedance • Signal-to-Noise Ratio: 75dB • Frequency Response: 20Hz - 20 kHz • Input Sensitivity: 150mV • T.H.D.: 0.3% • Bass/Treble: +/-10dB • 110V/220 Voltage Selector, 50/60Hz • Dimension (W x H x D): 7.48'' x 2.87'' x 5.31'' -inches www.PyleUSA.com 7

  • 1
  • 2
  • 3
  • 4

Features:
• Hi-Powered Component Amplifier System
Compact Desktop Receiver System Design
Built-in Wireless BT Audio Streaming
Works with All of Today's Latest Wireless BT Devices
Smartphones, Tablets, Laptops, Computers, etc.
USB/SD/FM playing
• Switchable Mic Pager and Mixing/Karaoke Modes
Page Mode: Allows Voice Transmission via Mic
Mix Mode: Allows Both, Voice & Music Transmission
RCA Audio Input (AUX 1, AUX 2, CD)
AUX (3.5mm) Input Connector Jack
(Connect Devices like Smartphones, Tablets, MP3 Players, etc.)
Treble, Bass, Balance, Master Volume Adjustable
Four Push Type Speaker L/R Terminals
Input Selector Switch
RCA Record Output
• 1/4'' Headphone Output
1/4” Mic Input Jack
Built-in Short Circuit and Power Surge Protection
• Compatible with Audio/Computerized Devices
Rotary Master & Microphone Volume Controls
Front Facing Control Panel
LED Indicator Lights
Wireless BT Connectivity:
Built-in Wireless BT Audio Receiver
Simple Pairing for Wireless Music Streaming
Works with All of Today’s Latest Wireless BT Devices
(Smartphones, Tablets, Laptops, computers, etc.)
Wireless BT Version: 5.0
Wireless BT Network Name: ‘
PYLEUSA
Wireless Range: Up to 40’ ft.
Technical Specs:
Power Output: 40 Watt x 2 (MAX)
10% RMS at 4-Ohm Impedance
Signal-to-Noise Ratio: 75dB
• Frequency Response: 20Hz - 20 kHz
Input Sensitivity: 150mV
• T.H.D.: 0.3%
Bass/Treble: +/-10dB
• 110V/220 Voltage Selector, 50/60Hz
• Dimension (W x H x D): 7.48'' x 2.87'' x 5.31'' -inches
IMPORTANT
Replacing a fuse
This amplifier requires fuse with the proper
rating for protection from power surges and
short circuits. If the amplifier suddenly turns
off or would not turn on, the fuse is properly
blown.
Let the amplifier cool down and see if it starts again before you
assume a fuse needs to be replaced.
Unplug the amplifier from the AC outlet.
Turn the fuse holder cap and pull out the cap.
Remove the old fuse and replace it with an identical one.
CAUTION:
Never use a fuse with a higher rating
TROUBLESHOOTING
www.PyleUSA.com
6
www.PyleUSA.com
7
NO POWER
The fuse might be blown
Check the amplifier's fuse
and replace it if necessary.
NO SOUND
Sound source or speakers
may not be connected
properly
Check
all connections
Master volume control
may be set to a minimum
Adjust the volume control
to a higher setting
The speaker's wire
might have the wrong
impedance
Make sure that the speakers
that you have connected to
the amp are
matching in
impedance
The amplifier is shutting
down or powering off
Turn the amplifier
off and let it
cool, make sure that the
amplifier is properly ventilated,
and
then tum it back on
Feedback
Microphone and speakers
are to close together
Reposition the microphone
and speakers