RCA 25110RE3-A User Guide - Page 32

Replacing the Batteries - replacement batteries

Get RCA 25110RE3-A - ViSYS Cordless Phone Call Waiting Caller ID PDF manuals and user guides
UPC - 940356373734
View all RCA 25110RE3-A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Other Information Replacing the Batteries Handset Battery CAUTION: To reduce the risk of fire or personal injury, only use Thomson Inc. approved Ni-MH-battery model 5-2683. 1. Make sure the telephone is OFF (not in TALK mode) before you replace battery. 2. Remove the battery compartment door. 3. Disconnect the cord attached to the battery pack from the jack inside the battery compartment and remove the battery pack. 4. Insert the new battery pack and connect the plug on the battery pack to the jack inside the compartment. NOTE: It is important to maintain the polarity (black and red wires) to the jack inside the compartment. To ensure proper battery installation, the connector is keyed and can be inserted only one way. 5. Close the battery compartment by pushing the door up until it snaps into place. 6. Place the handset in the charging cradle. Allow the handset battery to properly charge (for 16 hours) prior to first use or when you install a new battery pack. If you do not properly charge the phone, battery performance will be compromised. PRESS DOWN FIRMLY Handset Memory Retention When battery is disconnected the handset has the capability to hold the user memory and Caller ID memory for up to 5 minutes. BATTERY BLACK WIRE RED WIRE 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
32
Replacing the Batteries
Handset Battery
CAUTION:
To reduce the risk of fire or personal injury, only use Thomson Inc. approved
Ni-MH-battery model 5-2683.
1.
Make sure the telephone is
OFF
(not in TALK mode) before you replace battery.
2. Remove
the battery compartment door.
3.
Disconnect the cord attached to the battery pack from the jack inside the
battery compartment and remove the battery pack.
4.
Insert the new battery pack and connect the plug on the battery pack to the
jack inside the compartment.
NOTE:
It is important to maintain the polarity (black and red wires) to the jack inside the
compartment. To ensure proper battery installation, the connector is keyed and can be
inserted only one way.
5. Close the battery compartment by pushing the door up until it snaps into place.
6.
Place the handset in the charging cradle.
Allow the handset battery to properly charge (for 16 hours) prior to first use or when you
install a new battery pack. If you do not properly charge the phone, battery performance
will be compromised.
Handset Memory Retention
When battery is disconnected the handset has the capability to hold the user
memory and Caller ID memory for up to 5 minutes.
Other Information
BLACK WIRE
RED WIRE
BA
TTERY
PRESS DOWN
FIRMLY