RCA 25204RE1 User Guide - Page 31

Other Information - 2 line corded speakerphone

Get RCA 25204RE1 - ViSYS Corded Phone PDF manuals and user guides
UPC - 044319502480
View all RCA 25204RE1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Other Information 1. FLAT - No equalization adjustment is applied to the tone 2. LOW - Emphasizes the deep rich bass tones of the conversation 3. HIGH - Emphasizes the higher and sharper tones of the conversation 4. VOICE CLARITY - Optimizes your speakerphone tone and sound quality Like the self-calibration described above, the tone equalizer is only activated when speakerphone mode is activated. If you press the Preset EQ button while using the handset or a headset, you will hear an error beep, but there will be no difference in the tone of the conversation. Display Messages The following special messages indicate the status of a message or the unit: NO CALLS The CID memory log is empty. UNKNOWN CALLER The incoming call does not have CID service or their service area is not linked to yours. If UNKNOWN CALLER appears along with a calling number, the name information for that number was not available. BLOCKED CALL The caller is registered as "Private Number" and their CID information is withheld. INCOMPLETE DATA Caller information has been interrupted or corrupted during transmission. REPLACE BATTERY You need to replace the batteries to prevent data/power loss. END OF LIST You are at the beginning or the end of the CID memory log. Troubleshooting Guide No dial tone • Check or repeat installation steps: Make sure the telephone line cords are connected to the phone and the wall jack. Make sure the cords are not damaged . • Make sure the hook switch pops up when the handset is lifted . • Check the SPEAKER button. Is the indicator off? 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
±1
1. FLAT - No equalization adjustment is applied to the tone
2. LOW - Emphasizes the deep rich bass tones of the conversation
3. HIGH - Emphasizes the higher and sharper tones of the conversation
4. VOICE CLARITY - Optimizes your speakerphone tone and sound quality
Like the self-calibration described above, the tone equalizer is only activated when
speakerphone mode is activated. If you press the Preset EQ button while using the
handset or a headset, you will hear an error beep, but there will be no difference in the
tone of the conversation.
Display Messages
The following special messages indicate the status of a message or the unit:
NO CALLS
The CID memory log is empty.
UNKNOWN CALLER
The incoming call does not have CID service or their service area
is not linked to yours. If
UNKNOWN CALLER
appears along with a
calling number, the name information for that number was not
available.
BLOCKED CALL
The caller is registered as “Private Number” and their CID
information is withheld.
INCOMPLETE DATA
Caller information has been interrupted or corrupted during
transmission.
REPLACE BATTERY
You need to replace the batteries to prevent data/power loss.
END OF LIST
You are at the beginning or the end of the CID memory log.
Troubleshooting Guide
No dial tone
•
Check or repeat installation steps:
Make sure the telephone line cords are connected to the phone and the wall jack.
Make sure the cords are not damaged .
•
Make sure the hook switch pops up when the handset is lifted .
•
Check the SPEAKER button. Is the indicator off?
Other Information