RCA 75350 User Manual - Page 4

First Things First

Get RCA 75350 PDF manuals and user guides View all RCA 75350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

First Things First Mounting procedure 1. If your cabinet does not have an overhang: (a) Position Template in desired location on EN underside of cabinet, flush with front edge. (b) Then tape Template in place, and go to Step 2 (Read "Caution"). FRONT EDGE OF CABINET MOUNTING TEMPLATE If your cabinet has an overhang: (a) Measure the thickness of the overhang. (b) Fold front of Template downward along the printed guideline that is closest to the thickness of your cabinet. (c) Tape fold-down portion to backside of overhang, Tape Template to cabinet underside. MEASURE THICKNESS OF CABINET OVERHANG FOLD TEMPLATE ON DOTTED LINE First Things First Note: If your cabinet has glue blocks or other obstructions, cut out corresponding areas on the Template to clear them. Do not cut out or cut through the screw holes indicated on the Template. It is recommended that safety glasses be worn while drilling screw holes to prevent the possibility of eye injury. 2. Drill 1/4 -inch diameter holes through the underside of the cabinet bottom shelf using the 3 points marked on the Template. 3. Remove Template and clean drill shavings from inside and underside of cabinet. 4. If your cabinet does not have an overhang, go to Step 5. If your cabinet has an overhang, select the spacer or combination of spacers that is equal to or longer than the cabinet overhang. Tips: On wooden cabinets you may want to mark and start the drill holes with a nail or an EN awl. Be sure to hold the drill very firmly against the cabinet to reduce "walking" of the drill bit from the markings. Use masking tape above the hole locations on inside of wooden cabinet shelf to help reduce splintering. If installing the unit under a wood cabinet, you may wish to countersink the drilled hole from the INSIDE of the cabinet if a countersink attachment for your drill is available. This will eliminate the use of washers and allow the screw heads to be flush with the floor of your cabinet. If you cannot countersink the holes, use the supplied washers. 3 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
EN
EN
First Things First
4
Note:
If your cabinet has glue blocks or other
obstructions, cut out corresponding areas on
the Template to clear them. Do not cut out or
cut through the screw holes indicated on the
Template.
It is recommended that safety glasses be worn
while drilling screw holes to prevent the
possibility of eye injury.
2.
Drill
1
/
4
-inch diameter holes through the
underside of the cabinet bottom shelf using
the 3 points marked on the Template.
3.
Remove Template and clean drill shavings
from inside and underside of cabinet.
4.
If your cabinet does not have an
overhang
, go to Step 5.
If your cabinet has an overhang,
select the
spacer or combination of spacers that is equal
to or longer than the cabinet overhang.
Tips:
On wooden cabinets you may want to
mark and start the drill holes with a nail or an
awl.
Be sure to hold the drill very firmly against the
cabinet to reduce “walking” of the drill bit
from the markings.
Use masking tape above the hole locations on
inside of wooden cabinet shelf to help reduce
splintering.
If installing the unit under a wood cabinet,
you may wish to countersink the drilled hole
from the INSIDE of the cabinet if a countersink
attachment for your drill is available. This will
eliminate the use of washers and allow the
screw heads to be flush with the floor of your
cabinet. If you cannot countersink the holes,
use the supplied washers.
First Things First
3
Mounting procedure
1.
If your cabinet does not have an
overhang:
(a)
Position Template in desired location on
underside of cabinet, flush with front
edge.
(b)
Then tape Template in place, and go to
Step 2 (Read “Caution”).
MEASURE THICKNESS OF
CABINET OVERHANG
FRONT EDGE
OF CABINET
MOUNTING
TEMPLATE
If your cabinet has an overhang:
(a)
Measure the thickness of the overhang.
(b)
Fold front of Template downward along
the printed guideline that is closest to
the thickness of your cabinet.
(c)
Tape fold-down portion to backside of
overhang, Tape Template to cabinet
underside.
FOLD TEMPLATE ON
DOTTED LINE