RCA RCRPS02GR Owner/User Manual - Page 1
RCA RCRPS02GR Manual
View all RCA RCRPS02GR manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
RCRPS02GR Universal Remote Control Owner's Manual Manual del Propietario (parte posterior) Tip: This remote is already programmed to operate many Samsung-branded TVs and DIRECTV-branded receivers. Just press the corresponding key-TV for a television, SAT•CBL• STREAM for a satellite receiver. Step 1: Install your batteries Your universal remote requires two AAA alkaline batteries (not included). To install the batteries: 1. Remove the battery compartment cover. 2. Insert the batteries, matching the (+) and (-) marks inside the battery compartment. 3. Push the battery cover back into place. Battery Precautions: • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. • Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with Local and National Regulations. Battery Saver Your universal remote control saves battery power by automatically turning off if any key is pressed for more than 60 seconds. This saves your battery life should your remote get stuck in a place where the keys remain depressed, such as between sofa cushions. Step 2: Program your remote To use this universal remote with your home entertainment system, first you need to program it to control your devices. There are two ways you can program the universal remote to operate your devices: • The Brand Code Search searches through the codes for select brands of devices. • The Direct Code Entry lets you enter a code from the accompanying code list for your brand of device. Brand Code Search The Brand Code Search goes through only the codes for one of the select brands listed in the accompanying code list. If your brand of device is listed, this search can be very quick and easy. IMPORTANT: The Brand Code Search works for TVs, satellite receivers and cable boxes. The Brand Code Search does not work for programming this remote to control digital converter boxes and streaming players. Use direct code entry for these kinds of devices. TIPS: Each device key is associated with a type of device-the TV is preset to search for TVs, SAT•CBL•STREAM for satellite receivers, digital TV converters, cable boxes, or streaming players. If the original remote control that came with your device has separate ON and OFF keys (instead of a single POWER key), the Brand Code Search might not work with that device. Try the Direct Code Entry method described later in this manual. To exit without saving a new code at any point in the Brand Code Search, press EXIT•BACK key. 1. Manually turn on the device you want to control. LLiisCsttoeadddeeeLsiCscótosddi/geos/s BBSrrLeaLaàainGensrLslduLc'tduaihrocieCsdtieosdiCometsldiedcadazCCoedeóaleedóotstednddasehsddddid0leioeeagg'l1eoo0cua/droo2e0LtComeserio3leilundiódusascmsetreahltdelaqtiéesdlnieuatgrgueoecsfduPRdoorhds.íRmeCraTeosisOHAnVpaoIdddmniS,drrtnteuesaGocChtelicaagAgEecbhuusrrn,oNúMitsUaqisdisaumlosiequaasenmuérerdries'cuoesidnt.apmGiaglosiuzdauuPRairersDdRdCqielVOcnoAuaAI.óDgsnSe,ppdsGCptderiiJhAgEgoaxéVen,NorgcCaisrraBiaptrdmeareondmmgdaarnaCatVsirmooPRcCldRnaeCaRMesOrA/P,MaJS,PVgPVGCihnaRtCsiAEnalui,Nvapbossioxsnh, iic 04 05 06 JVC LG MaPghnialivposx, Mitsubishi LG MaPghnialivposx, Memorex Panasonic Samsung Sharp Sony TIVO 07 Panasonic Pioneer Toshiba 08 Samsung Samsung 09 Sanyo Sanyo 10 Sharp Sharp 11 12 13 14 Sony SEymlvearnsioan, Toshiba Vizio Sony Sylvania Toshiba 15 2. Find your device's brand in the Brand Code list section of the accompanying code list. Circle the number for your brand and keep the list handy. 3. Press and hold the device key you want to program (the POWER key illuminates). While you're holding down the device key, use your other hand to press and hold the remote's POWER key at the same time (the POWER key turns off). 4. Wait until the POWER key comes on and stays on. Then release both keys. 5. Look at the numbers you circled for your device's brand code. Press those numbers on the remote keypad. Note: For single-digit brand codes, press the 0 key first (for example, 0-5 for 5). 6. Point the remote directly at the front panel of the device you want to control. Press GUIDE on the remote and wait 2 seconds. The remote is sending a single code for your device's brand. Did your device turn off? YES: Press the POWER key to turn your device back on. Then test the following keys to make sure they work: VOL+ (for TVs), CH+, and the 0 digit. If these keys work, press OK/ENTER to save this code. You've finished programming this key. NO: Press GUIDE again. The remote sends the next code for your brand. Keep pressing GUIDE every 2 seconds until your device turns off. When it does, follow the "YES" instructions above. NOTES: Throughout the programming of each key, be sure to keep the remote pointed at the IR sensor of the device you are currently programming the remote to control. Test the remote with the device to make sure the device key is programmed with the correct code for maximum functionality. If some features don't work, try a different code. See the "Testing the Code for Maximum Functionality" section below for more information. During the Brand Code Search, the remote ignores keypresses that aren't part of the search. Search keys are VOL+, CH+, POWER, and 0. The search times out after two minutes (the POWER key blinks four times and the last programmed code under that device key is retained). The POWER key blinks four times when the remote has gone through all the codes. The remote exits the Brand Code Search. If your device hasn't turned off yet, try direct code entry.. Testing the Code for Maximum Functionality 1. Try a variety of the device's functions with the remote. If some device features don't work, go to the next step to try a different code. 2. Repeat the Brand Code Search from the beginning. When the device turns off for the first time, don't press the OK/ENTER key, which would store the same code. Instead, with the unit now off, continue to press the GUIDE key repeatedly until the unit turns back on. 3. Once the unit turns back on, you have found another code that operates the device. Press the OK/ENTER key. 4. Test the key's functionality again by attempting to control a variety of the device's functions. If the code that has been stored controls the majority of the device's functions, programming is complete. If the code stored does not give maximum functionality, try another code. Direct Code Entry Direct Code Entry lets you enter a code from the accompanying code list for your brand of device. TIPS: Each device key is associated with a type of device-the TV is preset to search for TVs, SAT•CBL•STREAM for satellite receivers, digital TV converters, cable boxes, or streaming players. LLiisCsttoeadddeeeLsiCscótosddi/geos/s BBSrrLeaLaàainGensrLslduLc'tduaihrocieCsdtieosdiCometsldiedcadazCCoedeóaleedóotstednddasehsddddid0leioeeagg'l1eoo0cua/droo2e0LtComeserio3leilundiódusascmsetreahltdelaqtiéesdlnieuatgrgueoecsfduPRdoorhds.íRmeCraTeosisOHAnVpaoIdddmniS,drrtnteuesaGocChtelicaagAgEecbhuusrrn,oNúMitsUaqisdisaumlosiequaasenmuérerdries'cuoesidnt.apmGiaglosiuzdauuPRairersDdRdCqielVOcnoAuaAI.óDgsnSe,ppdsGCptderiiJhAgEgoaxéVen,NorgcCaisrraBiaptrdmeareondmmgdaarnaCatVsirmooPRcCldRnaeCaRMesOrA/P,MaJS,PVgPVGCihnaRtCsiAEnalui,Nvapbossioxsnh, iic 04 05 06 JVC LG MaPghnialivposx, Mitsubishi LG MaPghnialivposx, Memorex Panasonic Samsung Sharp Sony TIVO 07 Panasonic Pioneer Toshiba 08 Samsung Samsung 09 Sanyo Sanyo 10 Sharp Sharp 11 12 13 14 Sony SEymlvearnsioan, Toshiba Vizio Sony Sylvania Toshiba 15 1. Manually turn on the device you want to control. 2. Find the Code List that came with the remote. Locate the section for the type of device you're trying to program, and find your brand in that section. Circle the codes for your brand and keep them handy. 3. Press and hold the device key you want to program (the POWER key comes on). While you're holding down the device key, use your other hand to enter the first five-digit code for your brand in the code list (the POWER key goes off after the first digit). 4. When you've finished entering the five-digit code, keep holding down the device key and look at the POWER key. Is the POWER key illuminated? YES: You're done! You've programmed this device key. NO, it blinked four times and turned off: You have either entered a code number that is not in the code lists or missed a step in the code entry procedure. Try step 3 again. 5. Now test the device with your TV on. Try the the VOL+,CH+ and the digit "0". If these work correctly, then you have the correct code . If not go to step 3 and try the next code in the list. NOTES : Test the remote with the device to make sure the device key is programmed with the correct code for maximum functionality. If some features don't work, try a different code in the list. Remember to enter the code for future reference in the box provided in the Code Retrieval section of this manual. If you release the device key any time during the Direct Code Entry procedure, the POWER key blinks four times and the process is exited. The last programmed code under the device key is retained. Step 3: Program Your Preset Channels This remote control gives you access to up to 10 of your favorite satellite or cable and TV channels instantly, using the Preset Keys. For example, if one of your favorite channels is ESPN, you can set up this remote to take you directly to that channel when you press the P key followed by the 1 key. To use the Preset Channels feature, first you must program the channel you'd like to use for each Preset key. Before you start, use the following table to gather information about your favorite channels. You can set up 10 favorites for each channel source: 10 for SAT/CBL/STREAM and 10 for TV. EXAMPLE: Preset Channel Key 1 Network ESPN Channel Number 202 Preset Ch Preset Ch • Preset ch TV conve that kind • Set up all set up yo confusing