Rane CP52S CP52S Installation Manual - Page 11

CP52S COMMERCIAL PROCESSOR INPUT TRIM DETECT THRESHOLD +30 +60 MIC LINE OL ACTIVE PAGING PROGRAM INPUT LEVELS ZONE LEVEL 4 6 LIMIT THRESHOLD +8 2 8 -3 +16 LINE 1 4 6 2 0 10 -20 +20 0 10 LIMIT LINE 2 4 6 0 10 LINE 3 4 6 0 10 PRIORITY 4 6 8 DUCKER DEPTH PROGRAM SELECT L2 L3 L1 P REMOTE LEVEL 4 6 LIMIT THRESHOLD +8 2 8 -3 +16 OFF ON 0 10 0 10 SIG OL -20 +20 LIMIT EQ + 12 • 6 • 0 • 6 • 12 40 100 250 630 1.6k 4k 10k POWER CP52S COMMERCIAL PROCESSOR CP52S COMMERCIAL AUDIO 100-240 V EQUIPMENT 24TJ 50/60 Hz 12 WATTS R ZONE REMOTE PROGRAM LEVEL D1 D0 MIN MAX Vr Vc ACN 001 RANE CORP. MADE IN U.S.A. 345 482 D1 D0 Vr Vc ZONE OUTPUT EXPAND OUTPUT RIGHT +- LEFT +- MONO EXPAND +- SOURCE LEVEL +- +- +- ZONE PAGE PROGRAM RELEASE PRIORITY 3 PROGRAM INPUTS 2 1 L L DETECT THRESHOLD 5 20 SEC OFF ON R R ALL AUDIO AND REMOTES ARE CLASS 2 WIRING PAGING INPUT PAGE LEVEL TRACKS ZONE LEVEL LOW / HIGH CUT FILTER MIC PHANTOM POWER OFF ON OUT IN OFF ON 100 Hz / 7 kHz +15V INPUT +- +- CALIBRATION 1. Connect the power supply and verify the POWER indicator lights. 2. Verify the Zone LEVEL control is set to maximum and that an active source is playing for each of the Program Inputs intended for use. Select each Program Input and adjust its Input Level control to be the very loudest you would ever desire. 3. Adjust the Zone LIMIT THRESHOLD so that it just starts to audibly reduce the output level. This ensures that the level will never be louder than the maximum level just set. 4. Turn the Zone LEVEL control down to a comfortable listening level. 5. Note that with the Paging LEVEL set to minimum, the following Page will not be heard. Speak very loudly (bark) into the Paging mic. Adjust the INPUT TRIM control so that the Paging Overload indicator just lights. It is important to set the gain of the preamp before setting the Paging Detect Threshold. 6. Speak into the Paging mic in a normal voice and adjust the Paging DETECT THRESHOLD so the ACTIVE indicator lights only during speech. If the Paging Detect Threshold is set too low, the Pager may gate on due to background sound. 7. With an active Program source playing, speak into the Paging mic. Adjust the Paging LEVEL control to provide the correct Pageto-Program mix. If the Paging Detect Threshold is set too high, there may be a delay before speech is heard. To correct this, lower the Paging Detect Threshold setting. 8. Set the Paging LIMIT THRESHOLD to limit the maximum Page level to the loudest desired volume. 9. Set the DUCKER switch to ON. With an active Program source playing, speak into the Page mic and adjust the DUCKER DEPTH to the desired level of Program during a Page. 10. Set the rear panel Program PRIORITY OFF / ON switch as required. If an automatic Program Priority override is not required, set this switch to OFF. The front panel PROGRAM SELECT switch will select the "P" Program Input just like any other nonpriority Input. 11. If using a ZR1 Remote, press the RMT switch in and verify that the remote functions correctly (see page Manual-4). 12. Adjust the Equalizer as desired. SECURITY Rane offers a few options to protect the settings you just made. To protect the equalizer section, use a Rane SCP1S security cover. To protect the setting of any rotary control, remove the knob and replace with one of the hole plugs included with the SCP1S. To protect the entire front panel and allow operation with only the ZR1 Remote, use a Rane SC 1.7. You're all set. Enjoy. 11