Rane MP26 MP26 Mixer Owners Manual - Page 10

MP26 CLUB MIXER BOOTH 4 6 2 8 0 10 LEVEL PHONES 4 6 2 8 0 10 LEVEL CUE MAIN PAN SPLIT CUE MIC 1 4 6 2 8 0 10 LEVEL LEFT RIGHT PAN MIC 2 4 6 2 8 0 10 LEVEL LEFT RIGHT PAN PGM 1 A1 A2 D1 A3 P1 A4 SOURCE 4 6 2 8 0 10 LEVEL OFF +6 HIGH OFF +6 MID PGM 2 A1 A2 D2 A3 P2 A4 SOURCE 4 6 2 8 0 10 LEVEL OFF +6 HIGH OFF +6 MID PGM 3 A1 A2 D3 A3 P3 A4 SOURCE 4 6 2 8 0 10 LEVEL OFF +6 HIGH OFF +6 MID PGM 4 A1 A2 D4 A3 P4 A4 SOURCE 4 6 2 8 0 10 LEVEL OFF +6 HIGH OFF +6 MID OFF +6 HIGH OFF +6 LOW FLEXFX MIC ON TALKOVER OFF +6 HIGH OFF +6 LOW FLEXFX MIC ON TALKOVER LOW HIGH FILTER FLEXFX 10 9 8 CUE 7 6 5 4 3 2 1 0 OFF +6 LOW A B POST LOW HIGH FILTER FLEXFX 10 9 8 CUE 7 6 5 4 3 2 1 0 OFF +6 LOW A B POST LOW HIGH FILTER FLEXFX 10 9 8 CUE 7 6 5 4 3 2 1 0 OFF +6 LOW A B POST LOW HIGH FILTER FLEXFX 10 9 8 CUE 7 6 5 4 3 2 1 0 OFF +6 LOW A B POST FLEXFX 4 6 2 8 0 10 SEND 4 6 2 8 0 10 RETURN EXT LOOP USB LOOP FILTER F ECHO ̇ BEAT CONTOUR TAP Mixer Controls Mic Inputs Two Microphone Inputs are independent, each with these controls: • Level control. • Pan the signal from Left to Right. • High / Low 2-band, full-cut tone controls. The range is Off to +6 dB, with unity gain at 12 o'clock. • FlexFX Assign takes the signal out of the Main Mix and sends it to the FlexFX Loop. • Mic On adds the Mic to the Main Mix as a program input. If Talkover is engaged on the other Mic, this Mic is ducked like any other program input. • Talkover engages the Mic in the Main Mix and ducks all program inputs. If Talkover is engaged on the other Mic, this Mic is not ducked. • Peak signal / rms meter displays the signal level with peakhold. • Mic 1 front panel connector is intended for a wired dynamic mic. A gooseneck mic is not recommended as it could damage the jack and not be covered under Rane's Warranty. • Mic 2 allows selection of a Mic- or Line-level input via the rear panel switch. Line-level is usually for wireless mics. • Mic 1, Mic 2, or the Main Mix may be recorded via USB Record-6. Record source selection is made in the computer's MP26 driver control panel. 10 Program Strips • Source selection: Each program input x may select from Px, Dx, A1, A2, A3, or A4. • Level is Off to +12 dB, with unity gain at 12 o'clock. • High / Mid / Low 3-band, full-cut tone control range is Off to +6 dB, with unity gain at 12 o'clock. • Filter with Low-pass and High-pass: • Flat response is in the center at 12 o'clock. • Low-pass filter cut-off moves from 20 kHz toward 20 Hz as the knob is turned counter-clockwise. • High-pass filter cut-off moves from 20 Hz toward 20 kHz as the knob is turned clockwise. • The filter resonance can be switched high or low in the computer's MP26 driver control panel. • The A-B-Post switch assigns the channel to A-side, B-side, or Post-Crossfader. • FlexFX assign takes the channel out of the Main Mix and sends it to the FlexFX Bus (post-fader). • Cue select assigns the channel to the headphones (pre-fader). • Channel meter displays mono signal level with peak-hold. • A 60 mm long-throw program fader controls the level of the channel in the Main Mix. • PGM 1-4 post-fader, stereo program channels are streamed to the computer via USB record channels 1-4. These channels may be recorded for post production editing and mix-down.