RedMax SRTZ2460 Owners Manual - Page 9

Set up

Get RedMax SRTZ2460 PDF manuals and user guides View all RedMax SRTZ2460 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

LRTZ2460/SRTZ2460 6. Set up ■ MOUNTING ENGINE (SE1) 1. Push the driveshaft housing toward the clutch housing and rotate it by hand to SE1 check that the driveshaft is engaged with the gears. 2. Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult to engage, twist the engine slightly. 3. Fasten the clamp securely with two screws. IMPORTANT Tighten the screws gradually by turns. SE2 ■ CONNECTING THROTTLE WIRE 1. Remove the air cleaner cover. 2. Connect the end of the throttle wire to the joint on the top of the carburetor. (SE2) SE3 (1) ■ CONNECTING SWITCH WIRES • Connect the switch wires between the engine and the main unit. Pair the wires of the same color. ■ INSTALLING HANDLE • Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. (SE3) (1) About 19 inches (48cm) SE4 (1) (3) (4) (5) (2) US-8 ■ ATTACHING THE TRIMMING MECHANISM (SE4) 1. Remove the screw screwed into the end of the trimming mechanism. 2. Insert the end of the trimming mechanism into the shaft tube. 3. Line up the hole on the end of the trimming mechanism into which the screw is to be inserted with the hole on the shaft tube, and screw the screw firmly in. 4. Using a wrench, screw in the bolt provided to fix the trimming mechanism into place. (1) Shaft tube (2) Trimming mechanishm (3) Screw hole (4) Bolt (5) Fastening bolt ■ BALANCE UNIT 1. Put on strap and attach unit to strap. 2. Depending on the working posture, slide clamp up or down until unit balances and the strap fits your body.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
US-8
LRTZ2460/SRTZ2460
6. Set up
■
MOUNTING ENGINE (SE1)
1. Push the driveshaft housing toward the
clutch housing and rotate it by hand to
check that the driveshaft is engaged
with the gears.
2. Insert the driveshaft housing into the
clutch housing until it bottoms, and
align the positioning holes on the clutch
housing and the shaft tube and install
the screw. When difficult to engage,
twist the engine slightly.
3.
Fasten the clamp securely with two
screws.
Tighten the screws gradually by turns.
■
CONNECTING THROTTLE WIRE
1. Remove the air cleaner cover.
2. Connect the end of the throttle wire to
the joint on the top of the carburetor.
(SE2)
■
CONNECTING SWITCH WIRES
•
Connect the switch wires between the
engine and the main unit. Pair the wires
of the same color.
■
INSTALLING HANDLE
•
Mount the handle to the shaft tube and
clamp it at a location that is comfortable
to you. (SE3)
(1) About 19 inches (48cm)
■
ATTACHING THE TRIMMING
MECHANISM (SE4)
1. Remove the screw screwed into the
end of the trimming mechanism.
2. Insert the end of the trimming
mechanism into the shaft tube.
3. Line up the hole on the end of the
trimming mechanism into which the
screw is to be inserted with the hole on
the shaft tube, and screw the screw
firmly in.
4. Using a wrench, screw in the bolt
provided to fix the trimming mechanism
into place.
(1) Shaft tube
(2) Trimming mechanishm
(3) Screw hole
(4) Bolt
(5) Fastening bolt
IMPORTANT
SE1
SE2
(1)
SE3
(5)
(4)
(3)
(2)
(1)
SE4
■
BALANCE UNIT
1. Put on strap and attach unit to strap.
2. Depending on the working posture,
slide clamp up or down until unit
balances and the strap fits your body.