Rocketfish RF-WHD210 Quick Setup Guide (English) - Page 2

Features, Remote control

Get Rocketfish RF-WHD210 PDF manuals and user guides View all Rocketfish RF-WHD210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

5 Switch the Power switches on the transmitter and receiver to the ON position (it does not matter which one you power on first). The HDMI input port LED on the transmitter should light continuously (stop blinking) to indicate that the desired input is selected. If this doesn't happen automatically, use the included remote control or HDMI Select Switch on the back of the transmitter to select the desired input port. For more details on HDMI port switching, see your User Guide. Note: The Power and Link Status indicator LED will flash while the transmitter and receiver establish a connection. Once the connection has been established, these indicators will light continuously (stop flashing). Note: The transmitter and receiver are pre-paired and should discover each other shortly after being powered on. However, should you experience an excessively long delay (over five minutes) for the link to be established, press the HDMI/WVAN switch on the back of the transmitter for at least three seconds to establish the link (the receiver must also be powered on during this process). For more detailed instructions on operating the WirelessHD kit, please refer to the included User Guide section, "Using the WirelessHD kit". Features Transmitter front/top panel Transmitter back panel Receiver front/top panel Receiver back and side panels # Component Description 1 HDMI 4 Lights to indicate that this HDMI input is selected. 2 HDMI 3 Lights to indicate that this HDMI input is selected. 3 HDMI 2 Lights to indicate that this HDMI input is selected. 4 HDMI 1 Lights to indicate that this HDMI input is selected. 5 Power and link status Blinking-Power is on and the transmitter is in sleep mode or indicator (transmitter) searching for the receiver. On-The transmitter and receiver are linked. Off-The power is off. 6 Power and link status Blinking-Power is on and the receiver is in sleep mode or indicator (receiver) searching for the transmitter. On-The transmitter and receiver are linked. Off-The power is off. 7 DC IN jack Connect the power adapter labeled"Transmitter"to this jack. 8 Power switch Turns the unit on or off. 9 HDMI select switch Press quickly (

  • 1
  • 2
5
Switch the Power switches on the transmitter and receiver to the ON position (it does not
matter which one you power on first). The HDMI input port LED on the transmitter should
light continuously (stop blinking) to indicate that the desired input is selected. If this doesn't
happen automatically, use the included remote control or HDMI Select Switch on the back of
the
transmitter to select the desired input port. For more details on HDMI port switching,
see your
User Guide
.
Note
: The Power and Link Status indicator LED will flash while the transmitter and receiver
establish a connection. Once the connection has been established, these indicators will light
continuously (stop flashing).
Note
: The transmitter and receiver are pre-paired and should discover each other shortly
after being powered on. However, should you experience an excessively long delay (over five
minutes) for the link to be established, press the HDMI/WVAN switch on the back of the
transmitter for at least three seconds to establish the link (the receiver must also be
powered on during this process).
For more detailed instructions on operating the WirelessHD kit, please refer to the included
User
Guide
section, “
Using the WirelessHD kit”
.
Features
Transmitter front/top panel
Receiver front/top panel
Transmitter back panel
Receiver back and side panels
Remote control
Note
: Remove the plastic film from the remote control before to using it for the first time.
One-year limited warranty
Visit www.rocket±shproducts.com for details.
Contact Rocketfish:
For customer service, please call 1-800-620-2790.
www.rocket±shproducts.com
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Rich±eld, MN 55423-3645 USA
© 2011 BBY Solutions, Inc., All Rights Reserved. ROCKETFISH is a trademark of BBY Solutions, Inc. All other products
and brand names are trademarks of their respective owners.
Best Buy Imports, S. de R.L. de C.V. Av. Santa Fe 485, Segundo Piso, Colonia Cruz Manca, Programa Parcial de
Desarrollo Santa Fe, Delegación Cuajimalpa, Distrito Federal, México 05349
© 2011 Best Buy UK Distributions Limited. All rights reserved. Distributed by Best Buy Europe Distributions Limited.
1 Portal Way, London W3 6RS
ENGLISH 11-0538
#
Component
1
HDMI 4
2
HDMI 3
3
HDMI 2
4
HDMI 1
5
Power and link status
indicator
(transmitter)
6
Power and link status
indicator
(receiver)
7
DC IN jack
8
Power switch
9
HDMI select switch
10
HDMI 1 jack
11
HDMI 2 jack
12
HDMI 3 jack
13
HDMI 4 jack
14
HDMI jack
15
DC IN jack
16
Power switch
17
Cable routing clips
Description
Lights to indicate that this HDMI input is selected.
Lights to indicate that this HDMI input is selected.
Lights to indicate that this HDMI input is selected.
Lights to indicate that this HDMI input is selected.
Blinking—Power is on and the transmitter is in sleep mode or
searching for the receiver.
On—The transmitter and receiver are linked.
Off—The power is off.
Blinking—Power is on and the receiver is in sleep mode or
searching for the transmitter.
On—The transmitter and receiver are linked.
Off—The power is off.
Connect the power adapter labeled “Transmitter” to this jack.
Turns the unit on or off.
Press quickly (<1 second) to switch HDMI inputs; or hold for at
least 3 seconds to join a Wireless Video Area Network (WVAN).
Connect an HDMI source device with a high-speed HDMI cable.
Connect an HDMI source device with a high-speed HDMI cable.
Connect an HDMI source device with a high-speed HDMI cable.
Connect an HDMI source device with a high-speed HDMI cable.
Connect this port to an HDMI input on the TV or projector, using
high-speed HDMI cable.
Connect the power adapter labeled “Receiver” to this jack.
Turns the receiver on or off.
Insert HDMI cable into these clips for receiver placement stability.