Ryobi P516 User Manual - Page 15

Mounting The Table Saw Base To The, Quickstand, To Install The Handle

Get Ryobi P516 PDF manuals and user guides View all Ryobi P516 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

SCREW ASSEMBLY LOCK NUT ARROWS LEG BRACE Fig. 7 HOLE LOCKING KNOB Fig. 6 MOUNTING THE TABLE SAW BASE TO THE QUICKSTAND® See Figure 8.  Place the table saw base on the leg stand. Position the locking knob over the holes in the top of the leg stand.  Insert the screw on the locking knob into the hole and turn the locking knob clockwise to secure the table saw base to the leg stand.  Repeat with the other three locking knobs. TO INSTALL THE HANDLE See Figure 9.  Hold the nylon nut securely and turn the screw counter- clockwise to remove the nut completely. NOTE: Do not remove the screw from the handle.  Place the nylon nut into the recessed hole on the back of the height/bevel adjusting handwheel and hold in place.  Slide the handle and screw into the hole on the height/ bevel adjusting handwheel.  Using a flathead screwdriver, turn the screw clockwise and tighten in place. NUT WASHER HEIGHT/BEVEL ADJUSTING HANDWHEEL 15 - English Fig. 8 HANDLE SCREW Fig. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
15 - English
ASSEMBLY
MOUNTING THE TABLE SAW BASE TO THE
QUICKSTAND
®
See Figure 8.
Place the table saw base on the leg stand. Position the
locking knob over the holes in the top of the leg stand.
Insert the screw on the locking knob into the hole and
turn the locking knob clockwise to secure the table saw
base to the leg stand.
Repeat with the other three locking knobs.
TO INSTALL THE HANDLE
See Figure 9.
Hold the nylon nut securely and turn the screw counter-
clockwise to remove the nut completely.
NOTE:
Do not remove the screw from the handle.
Place the nylon nut into the recessed hole on the back of
the height/bevel adjusting handwheel and hold in place.
Slide the handle and screw into the hole on the height/
bevel adjusting handwheel.
Using a flathead screwdriver, turn the screw clockwise
and tighten in place.
Fig. 8
LOCKING
KNOB
HOLE
Fig. 9
SCREW
NUT
Fig. 7
Fig. 6
HEIGHT/BEVEL
ADJUSTING HANDWHEEL
LOCK NUT
ARROWS
SCREW
HANDLE
WASHER
LEG BRACE