Ryobi RTS10NS Operation Manual - Page 16

Warning, Mounting Holes, To Install The Handle, To Remove/replace The Throat Plate

Get Ryobi RTS10NS PDF manuals and user guides View all Ryobi RTS10NS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

ASSEMBLY WARNING: To avoid serious personal injury, always make sure the table saw is securely mounted to a workbench or an approved leg stand. NEVER operate the saw on the floor. MOUNTING HOLES See Figure 6. The table saw must be mounted to a firm supporting surface such as a workbench or leg stand. Four bolt holes have been provided in the saw's base for this purpose. To mount the saw to a work bench, use bolts that are of sufficient length to accommodate the saw base, lock washers, hex nuts, and the thickness of the workbench or other mounting surface. Tighten all bolts or screws securely. Carefully check the workbench after mounting to make sure that no movement can occur during use. If any tipping, sliding, or walking is noted, secure the workbench to the floor before operating. TO INSTALL THE HANDLE See Figure 7.  Hold the nylon nut securely and turn the screw counterclockwise to remove the nut completely. NOTE: Do not remove the screw from the handle.  Place the nylon nut into the recessed hole on the back of the height/bevel adjusting handwheel and hold in place.  Slide the handle, screw, and washer into the hole on the height/bevel adjusting handwheel.  Using a flathead screwdriver, turn the screw clockwise and tighten in place. TO REMOVE/REPLACE THE THROAT PLATE See Figure 8.  Lower the blade by turning the height/bevel adjusting handwheel counterclockwise.  To remove the throat plate, place your index finger in the hole and lift the front end pulling the throat plate out toward the front of the saw.  To reinstall the throat plate, slip the tab into the slot at the back of the saw and push down to secure in place. MOUNTING HOLES MOUNTING HOLES Fig. 6 HANDLE SCREW WASHER NYLON HEIGHT/BEVEL NUT ADJUSTING HANDWHEEL THROAT PLATE Fig. 7 16 - English Fig. 11 Fig. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
16 - English
WARNING:
To avoid serious personal injury, always make sure the
table saw is securely mounted to a workbench or an
approved leg stand. NEVER operate the saw on the floor.
MOUNTING HOLES
See Figure 6.
The table saw must be mounted to a firm supporting surface
such as a workbench or leg stand. Four bolt holes have been
provided in the saw’s base for this purpose.
To mount the saw to a work bench, use bolts that are
of sufficient length to accommodate the saw base, lock
washers, hex nuts, and the thickness of the workbench or
other mounting surface. Tighten all bolts or screws securely.
Carefully check the workbench after mounting to make sure
that no movement can occur during use. If any tipping,
sliding, or walking is noted, secure the workbench to the
floor before operating.
TO INSTALL THE HANDLE
See Figure 7.
Hold the nylon nut securely and turn the screw counter-
clockwise to remove the nut completely.
NOTE:
Do not remove the screw from the handle.
Place the nylon nut into the recessed hole on the back of
the height/bevel adjusting handwheel and hold in place.
Slide the handle, screw, and washer into the hole on the
height/bevel adjusting handwheel.
Using a flathead screwdriver, turn the screw clockwise
and tighten in place.
TO REMOVE/REPLACE THE THROAT PLATE
See Figure 8.
Lower the blade by turning the height/bevel adjusting
handwheel counterclockwise.
To remove the throat plate, place your index finger in
the hole and lift the front end pulling the throat plate out
toward the front of the saw.
To reinstall the throat plate, slip the tab into the slot at
the back of the saw and push down to secure in place.
MOUNTING
HOLES
ASSEMBLY
MOUNTING
HOLES
Fig. 6
HEIGHT/BEVEL
ADJUSTING HANDWHEEL
Fig. 7
SCREW
NYLON
NUT
WASHER
HANDLE
THROAT
PLATE
Fig. 8