Ryobi RTS10NS Operation Manual - Page 37

Troubleshooting, Accessories, Maintenance

Get Ryobi RTS10NS PDF manuals and user guides View all Ryobi RTS10NS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

MAINTENANCE  Protect the blade by cleaning out sawdust from underneath the table and in the blade teeth. Use a resin solvent on the blade teeth.  Clean plastic parts only with a soft damp cloth. DO NOT use any aerosol or petroleum solvents. LUBRICATION All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. ACCESSORIES Look for these accessories where you purchased this product or call 1-800-525-2579:  Stand Assembly...089037007708 WARNING: Current attachments and accessories available for use with this product are listed above. Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury. TROUBLESHOOTING Problem Possible Cause Solution Excess vibration. Rip fence does not move smoothly. Rip fence does not lock at rear. Cutting binds or burns work. Blade is out of balance. Blade is damaged. Saw is not mounted securely. Work surface is uneven. Blade is warped. Rip fence not mounted correctly. Rails are dirty or sticky. Clamp nut is out of adjustment. Clamp nut is out of adjustment. Blade is dull. Blade is heeling. Work is fed too fast. Rip fence is misaligned. Wood is warped. Riving knife is out of alignment. Wood edges away from rip fence when Blade not properly sharpened or set. ripping. Replace blade. Replace blade. Tighten all hardware. Reposition on flat surface. Check saw blade installation. Replace blade if necessary. Remount the rip fence. Clean and wax rails. Adjust clamp nut counterclockwise. Adjust clamp nut clockwise. Replace or sharpen blade. See Adjusting the Blade Parallel to the Miter Gauge Groove (Removing Heel) in the Operation section. Slow the feed rate. Align the rip fence. Replace the wood. Always cut with convex side to table surface. See To Check and Align the Riving Knife and Saw Blade in the Assembly section. Resharpen or set blade. 37 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
37 - English
TROUBLESHOOTING
ACCESSORIES
Problem
Possible Cause
Solution
Excess vibration.
Blade is out of balance.
Blade is damaged.
Saw is not mounted securely.
Work surface is uneven.
Blade is warped.
Replace blade.
Replace blade.
Tighten all hardware.
Reposition on flat surface.
Check saw blade installation. Replace
blade if necessary.
Rip fence does not move smoothly.
Rip fence not mounted correctly.
Rails are dirty or sticky.
Clamp nut is out of adjustment.
Remount the rip fence.
Clean and wax rails.
Adjust clamp nut counterclockwise.
Rip fence does not lock at rear.
Clamp nut is out of adjustment.
Adjust clamp nut clockwise.
Cutting binds or burns work.
Blade is dull.
Blade is heeling.
Work is fed too fast.
Rip fence is misaligned.
Wood is warped.
Riving knife is out of alignment.
Replace or sharpen blade.
See
Adjusting the Blade Parallel to
the Miter Gauge Groove (Removing
Heel)
in the Operation section.
Slow the feed rate.
Align the rip fence.
Replace the wood. Always cut with
convex side to table surface.
See
To Check and Align the Riving
Knife and Saw Blade
in the Assembly
section.
Wood edges away from rip fence when
ripping.
Blade not properly sharpened or set.
Resharpen or set blade.
Look for these accessories where you purchased this product or call 1-800-525-2579:
Stand Assembly
.........................................................................................................................................
089037007708
WARNING:
Current attachments and accessories available for use with this product are listed above. Do not use any attachments
or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not
recommended can result in serious personal injury.
MAINTENANCE
Protect the blade by cleaning out sawdust from
underneath the table and in the blade teeth. Use a resin
solvent on the blade teeth.
Clean plastic parts only with a soft damp cloth. DO
NOT
use any aerosol or petroleum solvents.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication
is required.