Ryobi RTS22 Operation Manual - Page 34

Making A Bevel Cross Cut, Warning

Get Ryobi RTS22 PDF manuals and user guides View all Ryobi RTS22 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

OPERATION MAKING A BEVEL CROSS CUT See Figures 42 - 43. WARNING: Make sure the blade guard assembly is installed and working properly to avoid possible serious injury. VIEWED FROM THE FRONT, BELOW THE TABLE SAW BEVEL LOCKING LEVER TO TIGHTEN WARNING: The miter gauge must be on the right side of the blade to avoid trapping the wood and causing kickback. Placement of the miter gauge to the left of the blade will result in kickback and the risk of serious personal injury.  Remove the rip fence.  Unlock the bevel locking lever.  Adjust the bevel angle to the desired setting.  Lock the bevel locking lever.  Set the blade to the correct depth for the workpiece.  Set the miter gauge to 0° and tighten the lock knob.  Make sure the wood is clear of the blade before turning on the saw.  Turn the saw on.  Let the blade build up to full speed before moving the workpiece into the blade.  Hold the workpiece firmly with both hands on the miter gauge and feed the workpiece into the blade. NOTE: The hand closest to the blade should be placed on the miter gauge lock knob and the hand farthest from the blade should be placed on the workpiece.  When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing the workpiece. BLADE ANGLED TO LOOSEN HEIGHT/BEVEL ADJUSTING HANDWHEEL BEVEL CROSS CUT Fig. 42 MITER GAUGE STRAIGHT Fig. 43 34 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
34 - English
MAKING A BEVEL CROSS CUT
See Figures 42 - 43.
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid possible serious injury.
WARNING:
The miter gauge must be on the right side of the blade
to avoid trapping the wood and causing kickback.
Placement of the miter gauge to the left of the blade will
result in kickback and the risk of serious personal injury.
Remove the rip fence.
Unlock the bevel locking lever.
Adjust the bevel angle to the desired setting.
Lock the bevel locking lever.
Set the blade to the correct depth for the workpiece.
Set the miter gauge to 0° and tighten the lock knob.
Make sure the wood is clear of the blade before turning
on the saw.
Turn the saw on.
Let the blade build up to full speed before moving the
workpiece into the blade.
Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
NOTE:
The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
OPERATION
Fig. 42
VIEWED FROM THE FRONT, BELOW THE TABLE SAW
BEVEL
LOCKING
LEVER
TO
TIGHTEN
Fig. 43
BEVEL CROSS CUT
BLADE
ANGLED
HEIGHT/BEVEL
ADJUSTING
HANDWHEEL
TO
LOOSEN
MITER GAUGE
STRAIGHT