Samsung DV48J7700EW/A2 User Manual - Page 28

Final installation check list

Get Samsung DV48J7700EW/A2 PDF manuals and user guides View all Samsung DV48J7700EW/A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Installation Installation 5. Attach the 'Y" connector to the brass male end of the small hose. Screw on the coupling by hand until it is seated on the connector. 6. Using pliers, tighten the coupling with an additional two-thirds turn. NOTE Do not overtighten, as it may damage the coupling. 7. Attach the angled end of water hoses (C) to the fill valve at the bottom of the dryer rear frame. Screw on the coupling by hand until it is seated on the fill valve connector. 8. Using pliers, tighten the coupling with an additional two-thirds turn. NOTE Do not overtighten, as it may damage the coupling. 9. Turn the cold water faucet on. 10. Check for leaks around the "Y" connector, faucets and hoses. Final installation check list • The dryer is plugged into an electrical outlet and grounded properly. • The exhaust ductwork is hooked up and the joints are taped. • You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct. • The dryer is level and is sitting firmly on the floor. • For gas models: The gas is turned on and there are no gas leaks. • Start your dryer to confirm that it runs, heats, and shuts off. 28 English %7+2@&/64JOEE

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
28 English
Installation
Installation
5.
Attach the ‘Y” connector to the brass
male end of the small hose.
Screw on the coupling by hand until it is
seated on the connector.
6.
Using pliers, tighten the coupling with
an additional two-thirds turn.
NOTE
Do not overtighten, as it may damage the
coupling.
7.
Attach the angled end of
water hoses
(C)
to the fill valve at the bottom of the
dryer rear frame. Screw on the coupling
by hand until it is seated on the fill valve
connector.
8.
Using pliers, tighten the coupling with
an additional two-thirds turn.
NOTE
Do not overtighten, as it may damage the
coupling.
9.
Turn the cold water faucet on.
10.
Check for leaks around the “Y” connector,
faucets and hoses.
Final installation check list
•
The dryer is plugged into an electrical outlet and grounded properly.
•
The exhaust ductwork is hooked up and the joints are taped.
•
You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct.
•
The dryer is level and is sitting firmly on the floor.
•
For gas models: The gas is turned on and there are no gas leaks.
•
Start your dryer to confirm that it runs, heats, and shuts off.
DV7700J-03170Q-05_EN-US.indd
28
2015/11/3
11:28:07