Samsung DV5451AEW/XAA User Manual (user Manual) (ver.1.0) (English) - Page 18

Contents - review

Get Samsung DV5451AEW/XAA PDF manuals and user guides View all Samsung DV5451AEW/XAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

installing your dryer 6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step 7) or 4 Wire system instructions (Step 8) below. 7. Three Wire system instructions: a. Loosen or remove the center terminal block screw. b. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw of the terminal block. Tighten screw. c. Connect the other wires to outer terminal block screws. Tighten screws. d. Tighten the strain relief screws. e. Insert the tab of the terminal block cover into your dryer's rear panel slot. f. Secure the cover with a hold-down screw. g. BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section. If converting from a 4-wire electrical system to a 3-wire, you must connect the ground strap WARNING to the terminal block support to ground the dryer frame to the neutral conductor. We recommend using Ring terminals. If you use Strap terminals, please ensure you install them perfectly. 8. Four Wire System instructions: a. Remove the center terminal block screw. b. Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw. c. Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block. d. Connect the other wires to the outer terminal block screws. Tighten screws. e. Tighten the strain relief screws. f. Insert the tab of the terminal block cover into your dryer's rear panel slot. g. Secure the cover with a hold-down screw. h. BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section. We recommend using Ring terminals. If you use Strap terminals, please ensure you install them perfectly. 18_ Contents DV5471AE-03022A-01_EN.indd Sec2:18 2011-03-28 3:44:39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
18_
Contents
installing your dryer
6.
Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step
7) or 4 Wire system instructions (Step 8) below.
7.
Three Wire system instructions:
a.
Loosen or remove the center terminal block screw.
b.
Connect the neutral wire (white or center wire) of the power cord
to the center, silver-colored terminal screw of the terminal block.
Tighten screw.
c.
Connect the other wires to outer terminal block screws. Tighten
screws.
d.
Tighten the strain relief screws.
e.
Insert the tab of the terminal block cover into your dryer’s rear
panel slot.
f.
Secure the cover with a hold-down screw.
g.
BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section.
If converting from a 4-wire electrical system to a 3-wire, you must connect the ground strap
to the terminal block support to ground the dryer frame to the neutral conductor.
We recommend using Ring terminals. If you use Strap terminals, please ensure you install
them perfectly.
8.
Four Wire System instructions:
a.
Remove the center terminal block screw.
b.
Connect the ground wire (green or unwrapped) of the power cord
to the external ground conductor screw.
c.
Connect the neutral wire (white or center wire) of the power cord
and the appliance ground wire (green with yellow stripes) under the
central screw of the terminal block.
d.
Connect the other wires to the outer terminal block screws.
Tighten screws.
e.
Tighten the strain relief screws.
f.
Insert the tab of the terminal block cover into your dryer’s rear
panel slot.
g.
Secure the cover with a hold-down screw.
h.
BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section.
We recommend using Ring terminals. If you use Strap terminals, please ensure you install
them perfectly.
WARNING
DV5471AE-03022A-01_EN.indd Sec2:18
DV5471AE-03022A-01_EN.indd
Sec2:18
2011-03-28
3:44:39
2011-03-28
3:44:39