Samsung DVD-HD931 User Manual (ENGLISH) - Page 24

Controlling a TV with the Remote The remote can also be set up to control most TVs. To program the remote, use the code that corresponds to your brand. Code 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 TV Codes Brand SAMSUNG_1 SHARP_2 SONY MAGNAVOX SANYO_1 LG_2 RCA LG_1 TOSHIBA HITACHI JVC PANASONIC_1 MITSUBISHI_2 SAMSUNG_2 SAMSUNG_3 Code 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Brand SHARP_1 ZENITH LG_3 DAEWOO_8 SANYO_2 EMERSON SHARP_3 SAMSUNG_4 PANASONIC_2 NOBLEX TELEFUNKEN NEWSAN LOEWE RCA2 1 Turn on the TV 2 Point the DVD's remote at the TV. 3 While holding the TV POWER button down, enter the code for your brand. 4 If the TV turns off, setup is complete. Enter other codes of the same brand if the first code does not work. 5 To operate the TV, use the "TV Function Buttons" described on page 13. e.g) For Samsung_1 TVs While holding down the TV POWER button, enter 0 and then 1. NOTE The remote may not be able to control every model TV of the brands listed. 46 Troubleshooting Before requesting service (troubleshooting), please check the following. Problem No operations can be performed with remote. Disc does not play. 5.1 channel sound is not being reproduced. The icon appears on screen. Disc Menu doesn't appear. Play mode differs from the Setup Menu selection. The screen ratio cannot be changed. No audio. Forgot password If you experience other problems. Action • Check the batteries in the remote. May need replacing. • Operate the remote control at a distance of no more than 20 feet. • Remove batteries and hold down one or more buttons for several minutes to drain the microprocessor inside the remote to reset it. Reinstall batteries and try remote again. • Ensure that the disc is installed with the label side facing up. • Check the region number of the DVD. • 5.1 channel sound is reproduced only when the following conditions are met. : 1) The DVD player is connected with the proper amplifier 2) The disc is recorded with 5.1 channel sound. • Check whether the disc being played has the "Dolby 5.1 ch" mark on the outside. • Check if your audio system is connected and working properly. • In a SETUP Menu, is the Audio Output set to Bitstream? • The features or action cannot be completed at this time because: 1. The DVD's software restricts it. 2. The DVD's software doesn't support the feature (e.g., angles). 3. The feature is not available at the moment. 4. You've requested a title or chapter number or search time that is out of range. • Check if the disc has a Menu. • Some of the functions selected in the Setup Menu may not work properly if the disc is not encoded with the corresponding function. • The Screen Ratio is fixed on your DVDs. • Make sure you have selected the correct Digital Output in the Audio Options Menu. • Press power on from a cold start with no disc in the unit. Press the STOP ( ) and PLAY ( ) buttons simultaneously on the front panel for three seconds. The Select Menu Language display will appear. Select the desired language button. Press the MENU button on the remote control to select the Parental Mode. The Parental Mode is now unlocked as indicated on the display. Press the DOWN button to select Parental. Press ENTER and the Create Password display will appear. You can now set your rating level and change your password to a new number. • Go to the contents and find the section of the instruction book that contains the explanations regarding the current problem, and follow the procedure once again. • If the problem still cannot be solved, please contact your nearest samsung authorized service center. Page P5 P8 P14 P42 P20 P23 P37~45 P43 P42 P44~45 47 REFERENCE