Samsung DVE52M8650V/A3 User Manual - Page 24

Vent blockage test - dryer model not heating

Get Samsung DVE52M8650V/A3 PDF manuals and user guides View all Samsung DVE52M8650V/A3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Installation Installation STEP 6 Power on (Gas models) Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer's installation and operation using the final checklist in Step 7 below. STEP 7 Final Check When installation is complete, confirm that: • The dryer is plugged into an electrical outlet and grounded properly. • The exhaust ductwork is connected and the joints are taped. • You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct. • The dryer is level and is sitting firmly on the floor. • The dryer starts, runs, heats, and shuts off properly. For gas models: • The gas is supplied properly with no leaks. CAUTION The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5 minutes. Be sure the gas supply to your dryer has been turned on. To confirm gas ignition, check the exhaust for heat. Vent blockage test After the dryer is installed, start the Vent Blockage Test to check if the duct system is properly installed. The Vent Blockage Test automatically detects the status of duct and reports any blockage or problems to the user. Proper ducting can reduce drying time and save energy. NOTE The Vent Blockage Test must run at cool state. If the dryer warms up after the installation check, run the AIR FLUFF cycle for several minutes to reduce its internal temperature. Operation method 1. Make sure the drum is empty and close the door. (If there are any clothes or other items in the drum, a correct test can not be made.) 2. Press the POWER button to turn the dryer on, then simultaneously press and hold the Cycle 1 + Wrinkle Prevent buttons for 3 seconds. When entering the Vent Blockage Test, "InS" appears in the display. (If other procedures are started before entering the Vent Blockage Test, the dryer does not enter the Vent Blockage Test.) 24 English DV8650M-03170X-00_EN.indd 24 2017-01-06 4:36:58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Installation
Installation
English
24
STEP 6
Power on (Gas models)
Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then,
plug the power cord into a power source and check the dryer’s installation and operation
using the final checklist in Step 7 below.
STEP 7
Final Check
When installation is complete, confirm that:
•
The dryer is plugged into an electrical outlet and grounded properly.
•
The exhaust ductwork is connected and the joints are taped.
•
You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct.
•
The dryer is level and is sitting firmly on the floor.
•
The dryer starts, runs, heats, and shuts off properly.
For gas models:
•
The gas is supplied properly with no leaks.
CAUTION
The burner may not ignite initially due to air in the gas line. Allowing your dryer to
operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes,
turn your dryer off and wait 5 minutes. Be sure the gas supply to your dryer has been
turned on. To confirm gas ignition, check the exhaust for heat.
Vent blockage test
After the dryer is installed, start the Vent Blockage Test to check if the duct system is
properly installed. The Vent Blockage Test automatically detects the status of duct and
reports any blockage or problems to the user. Proper ducting can reduce drying time and
save energy.
NOTE
The Vent Blockage Test must run at cool state. If the dryer warms up after the installation
check, run the AIR FLUFF cycle for several minutes to reduce its internal temperature.
Operation method
1.
Make sure the drum is empty and close the door.
(If there are any clothes or other items in the drum, a correct test can not be made.)
2.
Press the
POWER
button to turn the dryer on, then simultaneously press and hold the
Cycle 1
+
Wrinkle Prevent
buttons for 3 seconds.
When entering the Vent Blockage Test, “
InS
” appears in the display.
(If other procedures are started before entering the Vent Blockage Test, the dryer does
not enter the Vent Blockage Test.)
DV8650M-03170X-00_EN.indd
24
2017-01-06
°° 4:36:58