Samsung DW80R5060 User Manual - Page 21

Completing The Installation

Get Samsung DW80R5060 PDF manuals and user guides View all Samsung DW80R5060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

02 INSTALLING THE DISHWASHER STEP 12 COMPLETING THE INSTALLATION 1. Open the door and remove all foam, paper packaging, and unnecessary parts. 2. Turn on the circuit breaker you turned off before you began the installation. 3. Open the water supply valve to supply water to the dishwasher. 4. Turn on the dishwasher, and then select and run a cycle. Check if the power turns on correctly and if there is any water leakage while the dishwasher is operating. If no errors occur while it is operating, turn off the dishwasher, and then go to Step 5 below. If an error has occurred, turn off the dishwasher, close the water supply valve, and then refer to the user manual or contact a service center 1-800-SAMSUNG (726-7864). Make sure to check for water leakage on both ends of the water supply line and drain hose CAUTION connector. 5. Confirm that the kick plate gasket is on the bottom of the kick plate. Insert the rubber skirt behind the kick plate, and tighten the kick plate using the screws included in the Install Kit. See the figures below for reference. Installation_DD81-02034B-020_EN.indd Sec3:21 installing the dishwasher _21 2/51/0/82/0210617 1100::5566::0066AAMM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
installing the dishwasher
_21
02 INSTALLING THE DISHWASHER
STEP 12
COMPLETING THE INSTALLATION
1.
Open the door and remove all foam, paper packaging, and unnecessary parts.
2.
Turn on the circuit breaker you turned off
before you began the installation.
3.
Open the water supply valve to supply water to the dishwasher.
4.
Turn on the dishwasher, and then select and run a cycle.
Check if the power turns on correctly and if there is any water leakage while the dishwasher
is operating. If no errors occur while it is operating, turn off
the dishwasher, and then go to
Step 5 below.
If an error has occurred, turn off
the dishwasher, close the water supply valve, and then
refer to the user manual or contact a service center 1-800-SAMSUNG (726-7864).
Make sure to check for water leakage on both ends of the water supply line and drain hose
connector.
CAUTION
Installation_DD81-02034B-00_EN.indd Sec3:21
Installation_DD81-02034B-02_EN.indd
Sec3:21
/10/2016 10:56:06 AM
25/08/2017
10:56:06 AM
5.
Confirm that the kick plate gasket is on the bottom of the kick plate. Insert the rubber skirt
behind the kick plate, and tighten the kick plate using the screws included in the Install Kit.
See the figures below for reference.