Samsung DW80R5061US/AA User Manual - Page 18

Case 2., With disposal, Disposal with an air gap, Without an air gap

Page 18 highlights

installing the dishwasher Case 2. With disposal With disposal Disposal with an air gap Air gap Without an air gap Drain hose Hose clamp Hose clamp 3. Check the size of the sink's drain hose connector. If needed, cut the drain hose so its end fits onto the sink connector (1" or 5/8" - as shown in Figure 11 below). If the end of the drain hose does not fit onto the drain hose connector of the sink, use an adaptor purchasable at a plumbing/hardware supply store. 4. Slide a hose clamp over the end of the drain hose. Attach the drain hose to the sink connector, slide the hose clamp to the end of the hose, and then tighten the hose clamp. Note : You must use a hose clamp. Failure to do so may cause water leakage. 5. If there is no air gap, make sure to hang. the middle of the drain hose well above the sink cabinet base to prevent backflow (see Figure 13 on the next page). 6. When drilling a hole for the drain hose on the cabinet wall, take caution not to damage the drain hose by sharp edges of the hole. On wooden walls, use sand paper to soften the edges. On metal walls, use insulation tape or duct tape to cover the sharp edges around the hole. 7. Take caution not the damage the drain hose when installing the dishwasher on the floor, wall, or cabinet. To prevent leaks or drainage problems, make sure the drain hose is not damaged, kinked, or twisted. 8. Do not cut the wrinkled area of the drain hose to fit the size. When arranging the drain hose, take caution not to contact on sharp edges of the cabinet or under-sink. • Be careful when cutting off the end of the drain hose as there is a risk of injury. Clean CAUTION around the sink's drain connection so that it does not damage the hose. Check for any foreign items in the drain hose and remove them. • When arranging the drain hose, make sure the drain hose is not cut, torn, or broken by any sharp edges of the floor, the product itself, or the cabinet. A damaged drain hose causes a leak. 18_ installing the dishwasher Installation_DD81-02034B-020_EN.indd Sec3:18 2/51/0/82/0210717 101:05:65:60:505AAMM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72

18_
installing the dishwasher
installing the dishwasher
Case 2.
With disposal
With disposal
Disposal with an air gap
Without an air gap
3.
Check the size of the sink’s drain hose connector. If needed, cut the drain hose so its end
fits onto the sink connector (1" or 5/8" - as shown in Figure 11 below). If the end of the drain
hose does not fit onto the drain hose connector of the sink, use an adaptor purchasable at a
plumbing/hardware supply store.
4.
Slide a hose clamp over the end of the drain hose. Attach the drain hose to the sink
connector, slide the hose clamp to the end of the hose, and then tighten the hose clamp.
Note : You must use a hose clamp. Failure to do so may cause water leakage.
5.
If there is no air gap, make sure to hang. the middle of the drain hose well above the sink
cabinet base to prevent backflow (see Figure 13 on the next page).
6.
When drilling a hole for the drain hose on the cabinet wall, take caution not to damage the
drain hose by sharp edges of the hole. On wooden walls, use sand paper to soften the edges.
On metal walls, use insulation tape or duct tape to cover the sharp edges around the hole.
7.
Take caution not the damage the drain hose when installing the dishwasher on the floor, wall,
or cabinet.
To prevent leaks or drainage problems, make sure the drain hose is not damaged, kinked,
or twisted.
8.
Do not cut the wrinkled area of the drain hose to fit the size. When arranging the drain hose,
take caution not to contact on sharp edges of the cabinet or under-sink.
• Be careful when cutting off
the end of the drain hose as there is a risk of injury. Clean
around the sink’s drain connection so that it does not damage the hose. Check for
any foreign items in the drain hose and remove them.
When arranging the drain hose, make sure the drain hose is not cut, torn, or broken
by any sharp edges of the floor, the product itself, or the cabinet. A damaged drain
hose causes a leak.
CAUTION
Air gap
Hose clamp
Drain hose
Hose clamp
Installation_DD81-02034B-00_EN.indd Sec3:18
Installation_DD81-02034B-02_EN.indd
Sec3:18
/10/2017
10:56:05 AM
25/08/2017
10:56:05 AM