Samsung HW-T450/ZA User Manual - Page 33

Update Procedure, If UPDATE is not displayed, Important, UPDATE, Power, NOTES

Get Samsung HW-T450/ZA PDF manuals and user guides View all Samsung HW-T450/ZA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Update Procedure If UPDATE is not displayed Important: The updating function erases all user settings. We recommend you write down your settings so that you can easily reset them after the update. Note that updating the firmware resets the subwoofer connection too. 1. Connect a USB thumb drive to the USB port on your computer. Important: Make sure there are no music files on the USB thumb drive. This may cause the firmware update to fail. 2. Go to the Samsung website https://www.samsung.com/us/support/ downloads/ on your computer  select Enter Model Number and enter the model of your Soundbar. Select manuals and downloads and download the latest software file. 3. Save the downloaded software to a USB stick and select "Extract Here" to unzip the folder. 4. Turn off the Soundbar and connect the USB stick containing the software update to the USB port. 5. Turn on the Soundbar and source change to "USB" mode. Within 3 minutes, "UPDATE" is displayed and updating begins. 6. When the update finishes, the Soundbar turns off (or turns off by press the (Power) button). Press the p button on the remote control for 5 seconds. "INIT" appears on the display and then the Soundbar turns off. The update is complete. •• This product has a DUAL BOOT function. If the firmware fails to update, you can update the firmware again. 7. Restore your settings on the Soundbar. 1. Turn off the Soundbar, disconnect and then reconnect the USB storage device that contains the update files to the Soundbar's USB port. 2. Disconnect the Soundbar's power cord, reconnect it, and then turn on the Soundbar. NOTES •• The firmware update may not work properly if audio files supported by the Soundbar are stored in the USB storage device. •• Do not disconnect the power or remove the USB device while updates are being applied. •• After the update is completed, the user setup in the Soundbar is initialized so you can reset your settings. We recommend you write down your settings so that you can easily reset them after the update. Note that updating firmware resets the subwoofer connection too. If the connection to the subwoofer is not re-established automatically after the update, refer to page 6. If the software update fails, check if the USB stick is defective. •• Mac OS users should use MS-DOS (FAT) as the USB format. •• Updating via USB may not be available, depending on the USB storage device manufacturer. ENG - 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
ENG - 27
Update Procedure
Important:
The updating function erases all user
settings. We recommend you write down your
settings so that you can easily reset them after
the update. Note that updating the firmware
resets the subwoofer connection too.
1.
Connect a USB thumb drive to the USB port
on your computer.
Important:
Make sure there are no music
files on the USB thumb drive. This may cause
the firmware update to fail.
2.
Go to the Samsung website
downloads/ on your computer
select Enter
Model Number and enter the model of your
Soundbar. Select manuals and downloads
and download the latest software file.
3.
Save the downloaded software to a USB
stick and select “Extract Here” to unzip the
folder.
4.
Turn off the Soundbar and connect the USB
stick containing the software update to the
USB port.
5.
Turn on the Soundbar and source change to
“
USB
” mode. Within 3 minutes, “
UPDATE
” is
displayed and updating begins.
6.
When the update finishes, the Soundbar
turns off (or turns off by press the
(Power)
button).
Press the
p
button on the remote
control for 5 seconds. “
INIT
” appears on the
display and then the Soundbar turns off.
The update is complete.
•
This product has a DUAL BOOT function.
If the firmware fails to update, you can
update the firmware again.
7.
Restore your settings on the Soundbar.
If UPDATE is not displayed
1.
Turn off the Soundbar, disconnect and then
reconnect the USB storage device that
contains the update files to the Soundbar’s
USB port.
2.
Disconnect the Soundbar’s power cord,
reconnect it, and then turn on the Soundbar.
NOTES
•
The firmware update may not work properly
if audio files supported by the Soundbar are
stored in the USB storage device.
•
Do not disconnect the power or remove the
USB device while updates are being applied.
•
After the update is completed, the user setup
in the Soundbar is initialized so you can reset
your settings. We recommend you write
down your settings so that you can easily
reset them after the update. Note that
updating firmware resets the subwoofer
connection too.
If the connection to the subwoofer is not
re-established automatically after the
update, refer to page
6
.
If the software update fails, check if the USB
stick is defective.
•
Mac OS users should use MS-DOS (FAT) as the
USB format.
•
Updating via USB may not be available,
depending on the USB storage device
manufacturer.