Samsung ME19R7041FS/AA Installation Guide - Page 10

D. Aligning The Wall Plate

Get Samsung ME19R7041FS/AA PDF manuals and user guides View all Samsung ME19R7041FS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Step-by-step installation guide D. ALIGNING THE WALL PLATE HHooleleAA CCeenntteerrllininee nnoottcchheess DDrraw a VveerrticcaallLliine on the wtoohnfaeTlWlcotapaoblClmifnaraoebrmtiknaeCtbtheoenvtece.ernter of CL HoHroizrioznontatal lLLiinnee AArrea E CAUTION: Wear gloves to avoid cutting CAUTIfiOngNe:rsWoneasrhagrlpoveedsgetso. avoid cutting fingers on sharp edges. Hole B Hoorriizzoonntatal Ll iLniene DDrraawwaahoHroizroizntoanl tlianlelionnethoenwwaalllal lfornogmthe bottom of bthoett"oRmearoWf a"lRl TeeamrpWlatael"l. Template". 1. Draw a horizontal line on the wall at the bottom of the "Rear Wall Template". 2. Drill ⅝˝ holes for toggle bolts in 3 locations (Hole A, Hole B, Hole C) as shown in the illustration above. If the location of a hole lines up with a stud, drill a 3/16˝ hole for a wood screw. You cannot use a toggle bolt to attach the wall plate to a stud. NOTE: DO NOT MOUNT THE PLATE AT THIS TIME. 3. Holes A, B and C are inside area E. If none of these holes line up with a stud, find a stud in area E that lines up with a hole circle in Area E, and then drill a 3/16˝ hole into it for a wood screw. You must have at least one wood screw mounted firmly into a stud to support the weight of the microwave. Set the mounting plate aside. 10 ME4000R_ME19R7041FS_AA_DE68-04585A-00_EN.indd 10 6/19/2019 4:23:10 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
10
Step-by-step installation guide
D. ALIGNING THE WALL PLATE
C
L
CAUTION:
Wear gloves to avoid cutting
Draw a horizontal line on the wall along the bottom of
the “Rear Wall Template”.
Draw a vertical line on the
wall to mark the center of
the cabinet above.
Horizontal Line
Horizontal Line
Area E
Centerline
notches
Hole A
Hole B
CAUTION
: Wear gloves to avoid cutting fingers
on sharp edges.
1
.
Draw a horizontal line on the wall at the
bottom of the “Rear Wall Template”.
2
.
Drill ⅝˝ holes for toggle bolts in 3 locations
(Hole A, Hole B, Hole C) as shown in the
illustration above. If the location of a hole
lines up with a stud, drill a
3
/
16
˝ hole for a
wood screw. You cannot use a toggle bolt to
attach the wall plate to a stud.
NOTE: DO NOT MOUNT THE PLATE AT
THIS TIME.
3
.
Holes A, B and C are inside area E. If none
of these holes line up with a stud, find a stud
in area E that lines up with a hole circle in
Area E, and then drill a
3
/
16
˝ hole into it for
a wood screw. You must have at least one
wood screw mounted firmly into a stud to
support the weight of the microwave.
Set
the mounting plate aside.
ME4000R_ME19R7041FS_AA_DE68-04585A-00_EN.indd
10
6/19/2019
4:23:10 PM