Samsung MultiXpress SCX-8623 User Manual Ver.1.03 (English) - Page 149
UI System Failure, Machine Setup
View all Samsung MultiXpress SCX-8623 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 149 highlights
Message Right door is open. Close it. Scanner locked or another problem occurred. Scan System Failure [error number]:Turn off then on. Second fax modem card is not installed. Install the card. Shake [color] toner cartridge. Side feeder door is open. Close it. Staple cartridge is empty. Replace it. Staple cartridge is low. Replace cartridge. Staple cartridge is not installed. Install it in finisher. Staple cartridge of booklet I is empty. Replace cartridge. Staple cartridge of booklet I is low. Replace cartridge. Meaning The door is not securely latched. The CCD (Charged Couple Device) lock has been locked. There is a problem in the scan system. The second optional fax multiline kit is not installed. Small amount of toner is left in the indicated cartridge. The door is not securely latched. The staple cartridge has reached the end of its lifespan. Small amount of staple cartridge is left. The estimated life of staple cartridge is close. The staple cartridge is not installed or the staple cartridge is not properly installed. The staple cartridge of booklet has reached the end of its lifespan. Small amount of staple cartridge of booklet is left. The estimated life of staple cartridge is close. Suggested solutions Close the door until it locks into place. Unlock the CCD lock . Or turn the machine off and back on again. If the problem persists, call for service. Scanner Turn the machine off and back on again. If the problem persists, call for service. Install the optional fax multiline kit. If it is already installed, try to reinstall the optional fax multiline kit. If the problem persists, call for service. You may temporarily increase the printing quality by redistributing the toner (see "Redistributing toner" on page 125). Close the door until it locks into place. This message appears when the staple cartridge is completely empty. Replace the staple cartridge. Prepare a new staple cartridge for a replacement. Install the staple cartridge. If it is already installed, try to reinstall the staple cartridge. If the problem persists, call for service. This message appears when the staple cartridge is completely empty. Replace the staple cartridge. Prepare a new staple cartridge for a replacement. Message Meaning Suggested solutions Staple cartridge of booklet I is not installed. Install the cartridge. The clock became initial time. Set a time again. Too much media in the center tray. Remove printed media. Too much media in booklet tray. Remove printed media. Too much media in finisher tray. Remove printed media. Top door of scanner is open. Transfer belt cleaning unit is not installed. Install it. Transfer belt is not installed. Install it. Transfer belt cleaning unit is worn. Replace with new one. Transfer belt unit is worn. Replace it. [tray number] cassette is pulled out. Insert it properly. [tray number] door is open. Close it. UI System Failure [error number]:Turn off then on. The staple cartridge of booklet is not installed or the staple cartridge is not properly installed. The time setting of machine is initialized. The center tray is full. The booklet tray is full. The finishing tray is full. The duplex automatic document feeder cover is not securely latched. The transfer belt cleaning unit is not installed. The transfer belt is not installed. The life of the transfer belt cleaning unit expires totally. The life of the transfer belt unit expires totally. The tray is not securely latched. The tray is not securely latched. There is a problem in the UI system. Install the staple cartridge. If it is already installed, try to reinstall the staple cartridge. If the problem persists, call for service. Set the time setting in Machine Setup. Remove printouts from the center tray, the machine resumes printing. Remove printouts from the booklet tray, the machine resumes printing. Remove printouts from the finishing tray, the machine resumes printing. Close the cover until it locks into place. Power off/on, if the problem persists, call for service. Power off/on, if the problem persists, call for service. Replace the transfer belt cleaning unit with a Samsung-genuine transfer belt cleaning unit, call for service. Replace the transfer belt unit with a Samsung-genuine transfer belt unit, call for service. Close the tray until it locks into place. Close the tray until it locks into place. Turn the machine off and back on again. If the problem persists, call for service. Troubleshooting_ 149