Samsung R7010 User Manual - Page 25

Troubleshooting - powerbot troubleshooting

Get Samsung R7010 PDF manuals and user guides View all Samsung R7010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Troubleshooting Symptom Checklist The POWERbot is not working at all. ffCheck if the emergency switch is on. ffCheck if all the icons are displayed on display panel. ffCheck if the battery of POWERbot is depleted. -- When "Lo" is displayed, carry POWERbot to the charger to charge it. ffReplace the batteries (AAA type) when the remote controller is not working. The POWERbot is stopped during cleaning process. ffWhen "Lo" is displayed on the display panel, carry POWERbot to the charger to charge it. ffWhen POWERbot is stuck by the obstacles such as cord, threshold etc, pick it up to remove it from the obstacle. -- If any fabrics or strings are caught in the drive wheel, turn off the emergency switch and remove the fabrics or strings before using it again. Suction power is weak. ffIf the "Filter inspection indicator" is on, turn off the emergency switch and clean the dustbin. ffWhen there's too much dust in the dustbin, suction power may get weakened. Turn off the emergency switch and empty the dustbin. ffIf the intake (on bottom of POWERbot) is blocked by foreign matters, turn off the emergency switch and remove foreign matter from the intake. ffWhen noise suddenly increase, turn off the emergency switch and empty the dustbin. The POWERbot cannot find the charger. ffCheck if there's power failure or whether the power plug is unplugged. ffRemove any obstacles around the charger that may disturb POWERbot from returning to the charger. ffWhen there's foreign matters on the charge pins that affects charging, clean the foreign matter. The POWERbot suddenly cleans diagonally. ffCheck if the charger is installed along the grain of wooden floors or tiles. ffIt may clean in diagonal direction for moving to another area in shortest route, or it made contact with any obstacles in that angle, or if it was charged at the charged at an angle, or grain of the wooden/tile floor is in that direction. Point cleaning is not working. ffIf you point the red light directly on POWERbot, it may not move to desired direction. -- Point the red light on the floor within 50 cm around POWERbot. ✻✻Do not use the point cleaning under direct sunlight, bright light or on dark floors. "Filter inspection indicator" is on even after the dustbin has been emptied. ffUse POWERbot after turning off the emergency switch and then turning it back on. ffEmpty the dustbin again and re-clean the filter thoroughly. The POWERbot passes ffIf the batteries are depleted, replace them. (2 type D (LR20) batteries) through the Virtual guard. ffIf the lamp is off, check if the Virtual guard is turned off and turn it on. The battery usage time of the Virtual guard is too short. ffCheck if you're using manganese drycell batteries and replace the batteries with new ones. (2 type D (LR20) batteries) ENGLISH-25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
ENGLISH-
25
Troubleshooting
Symptom
Checklist
The POWERbot is not
working at all.
f
Check if the emergency switch is on.
f
Check if all the icons are displayed on display panel.
f
Check if the battery of POWERbot is depleted.
–
When "Lo" is displayed, carry POWERbot to the charger to charge it.
f
Replace the batteries (AAA type) when the remote controller is not working.
The POWERbot
is stopped during
cleaning process.
f
When "Lo" is displayed on the display panel, carry POWERbot to the charger to
charge it.
f
When POWERbot is stuck by the obstacles such as cord, threshold etc, pick it
up to remove it from the obstacle.
–
If any fabrics or strings are caught in the drive wheel, turn off the emergency
switch and remove the fabrics or strings before using it again.
Suction power is weak.
f
If the "Filter inspection indicator" is on, turn off the emergency switch and clean
the dustbin.
f
When there's too much dust in the dustbin, suction power may get weakened.
Turn off the emergency switch and empty the dustbin.
f
If the intake (on bottom of POWERbot) is blocked by foreign matters, turn off
the emergency switch and remove foreign matter from the intake.
f
When noise suddenly increase, turn off the emergency switch and empty the
dustbin.
The POWERbot cannot
find the charger.
f
Check if there's power failure or whether the power plug is unplugged.
f
Remove any obstacles around the charger that may disturb POWERbot from
returning to the charger.
f
When there's foreign matters on the charge pins that affects charging, clean the
foreign matter.
The POWERbot
suddenly cleans
diagonally.
f
Check if the charger is installed along the grain of wooden floors or tiles.
f
It may clean in diagonal direction for moving to another area in shortest route,
or it made contact with any obstacles in that angle, or if it was charged at the
charged at an angle, or grain of the wooden/tile floor is in that direction.
Point cleaning is not
working.
f
If you point the red light directly on POWERbot, it may not move to desired
direction.
–
Point the red light on the floor within 50 cm around POWERbot.
±
✻
Do not use the point cleaning under direct sunlight, bright light or on dark floors.
"Filter inspection
indicator" is on even
after the dustbin has
been emptied.
f
Use POWERbot after turning off the emergency switch and then turning it back
on.
f
Empty the dustbin again and re-clean the filter thoroughly.
The POWERbot passes
through the Virtual
guard.
f
If the batteries are depleted, replace them. (2 type D (LR20) batteries)
f
If the lamp is off, check if the Virtual guard is turned off and turn it on.
The battery usage time
of the Virtual guard is
too short.
f
Check if you're using manganese drycell batteries and replace the batteries with
new ones. (2 type D (LR20) batteries)