Samsung RF261BIAESR User Manual Installation Guide Included Ver.1.0 (English, - Page 12

Completing The Set Up

Get Samsung RF261BIAESR PDF manuals and user guides View all Samsung RF261BIAESR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Do not use without the molded end (Bulb) CAUTION of the plastic tubing ( B ). T.igh1ten the compression nut ( B ) onto the compression fitting. Do not over-tighten the compression nut ( B ) . 2. Turn water on and check for any leakage. If you find water drops or leakage in the connection the connections and, if necessary, tighten. 3. Flush 1 gallon of water through the filter before drinking or using the water from the refrigerator. (Flush approximately 6 minutes.) To flush, press a large glass or cup against the water dispenser lever. Fill the glass, empty it into the kitchen sink after it is filled, and then repeat. 4. After you turn on the refrigerator, let the ice maker make ice for 1 to 2 days. Over that period of time, throw out the first 1 or 2 buckets of ice the freezer makes to ensure all impurities have been removed from the water line. Only connect the water line to a drinkable water source. If you have to repair or disassemble the water line, COMPLETING THE SET UP Now that you have your new refrigerator installed in place, you are ready to set up and enjoy the features and functions of the appliance. By completing the following steps, your refrigerator should be fully operational. 1. Make sure your refrigerator is in an appropriate location with reasonable clearance between it and the wall. Refer to installation instructions in this manual. 2. Once the refrigerator is plugged in, make sure the interior light comes on when you open the doors. 3. Set the Temperature control to the coldest temperature and wait for an hour. The freezer will get slightly chilled and the motor will run smoothly. Reset the refrigerator and freezer to the temperatures you want. 4. After you plug the refrigerator in, it will take a few hours to reach the appropriate temperature. You can store food and drinks in the refrigerator after the temperature is sufficiently cool. Under normal conditions, a 170 cc (5.75 oz.) cup can be filled in about 10 seconds. get a snug, leak-free connection. You can test the water line quickly using a paper cup. Under normal conditions, the about 10 seconds. 12_setting up 1.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
setting up
12_
Do not use without the molded end (Bulb)
of the plastic tubing (
B
).
Tighten the compression nut (
B
.
1
) onto the
compression fi
tting.
Do not over-tighten the compression nut (
B
) .
Turn water on and check for any leakage. If you
2.
fi
nd water drops or leakage in the connection
the connections and, if necessary, tighten.
Flush 1 gallon of water through the fi
lter
3.
before drinking or using the water from the
refrigerator. (Flush approximately 6 minutes.)
To fl
ush, press a large glass or cup against the
water dispenser lever. Fill the glass, empty it
into the kitchen sink after it is fi
lled, and then
repeat.
After you turn on the refrigerator, let the ice
4.
maker make ice for 1 to 2 days. Over that
period of time, throw out the fi
rst 1 or 2
buckets of ice the freezer makes to ensure all
impurities have been removed from the water
line.
Only connect the water line to a drinkable
water source.
If you have to repair or disassemble the water line,
get a snug, leak-free connection.
COMPLETING THE SET UP
Now that you have your new refrigerator installed
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your refrigerator
should be fully operational.
Make sure your refrigerator is in an appropriate
1.
location with reasonable clearance between it
and the wall. Refer to installation instructions in
this manual.
Once the refrigerator is plugged in, make sure
2.
the interior light comes on when you open the
doors.
Set the Temperature control to the coldest
3.
temperature and wait for an hour. The freezer
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to
the temperatures you want.
After you plug the refrigerator in, it will
4.
take a few hours to reach the appropriate
temperature. You can store food and drinks
in the refrigerator after the temperature is
suffi
ciently cool.
CAUTION
You can test the water line quickly using a
paper cup. Under normal conditions, the
about 10 seconds.
2012.5.16
3:2:1 PM
Under normal conditions, a 170 cc (5.75 oz.) cup
can be fi
lled in about 10 seconds.