Samsung RF323TEDBSR User Manual Ver.1.0 (English, French, Spanish) - Page 10

Making Minor, Adjustments Between, Doors, Installing The Water, Dispenser Line - review

Get Samsung RF323TEDBSR PDF manuals and user guides View all Samsung RF323TEDBSR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

MAKING MINOR ADJUSTMENTS BETWEEN DOORS Remember, a leveled refrigerator is necessary for getting the doors perfectly even. If you need help, review the previous section on leveling the refrigerator. Fixed part Adjustment part The left door is fixed. To make minor adjustments between doors, adjust only the right door. 1. Pull out the freezer drawer ( 1 ) to reveal the lower hinge ( 2 ). 2. Insert the supplied allen wrench (3/16") ( 3 ) into the shaft ( 4 ) of the lower hinge. 3. Adjust the height by turning the hex wrench ( 3 ) clockwise ( DOWN ) or counter clockwise ( UP ). When you turn the hex wrench counter- clockwise ( ), the door will move up. 2 3 3 4 1 2 fastener are enclosed with the refrigerator. The thickness of each fastener is 0.04". INSTALLING THE WATER DISPENSER LINE A water dispenser with a filter is one of the helpful features on your new refrigerator. To help promote better health, the water filter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You may need to purchase a water purifying system to do that. The water line also connects to the ice maker. For the ice maker to operate properly, water pressure of 20-125 psi (138 ~ 862Kpa) is required. If the refrigerator is installed in an area with low water pressure (below 20psi), you can install a booster pump to compensate for the low pressure. After you have connected the water line, make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water dispenser lever until the water runs from the water outlet. Water line installation kits are available at extra cost from your dealer. We recommend using a water line installation kit that contains copper tubing and ¼" compression nut. Connecting to the water supply line 1. First, shut off the main water supply. 2. Locate the nearest cold water drinking line and install the pipe clamp and shut off valve. 4. After adjusting the doors, insert the supplied fastener ( 6 ) using a pliers ( 5 ) in the gap between the hinge-grommet ( 7 ) and the lower hinge ( 8 ). The number of fasteners you'll need to insert depends on the gap. Cold water line Pipe clamp Shut off valve 3. Connect the water line installation kit to the shut off valve. 10_ setting up %""JOEC 1.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
10_
setting up
MAKING MINOR
ADJUSTMENTS BETWEEN
DOORS
Remember, a leveled refrigerator is necessary
for getting the doors perfectly even. If you need
help, review the previous section on leveling the
refrigerator.
The left door is fixed. To make minor
adjustments between doors, adjust only
the right door.
Pull out the freezer drawer (
1.
1
) to reveal the
lower hinge (
2
).
Insert the supplied allen wrench (3/16”) (
2.
3
)
into the shaft (
4
) of the lower hinge.
Adjust the height by turning the hex wrench (
3.
3
)
clockwise (
DOWN
DOWN
) or counter clockwise (
UP
UP
).
When you turn the hex wrench counter-
clockwise (
), the door will move up.
After adjusting the doors, insert the supplied
4.
fastener (
6
) using a pliers (
5
) in the gap
between the hinge-grommet
(
7
) and the lower
hinge
(
8
). The number of fasteners you’ll need
to insert depends on the gap.
2 fastener are enclosed with the refrigerator.
The thickness of each fastener is 0.04”.
INSTALLING THE WATER
DISPENSER LINE
A water dispenser with a filter is one of the helpful
features on your new refrigerator. To help promote
better health, the water filter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need
to purchase a water purifying system to do that.
The water line also connects to the ice maker.
For the ice maker to operate properly, water
pressure of 20-125 psi (138 ~ 862Kpa) is required.
If the refrigerator is installed in an area with low
water pressure (below 20psi), you can install
a booster pump to compensate for the low
pressure.
After you have connected the water line, make
sure the water storage tank inside the refrigerator
is properly filled. To do this, press the water
dispenser lever until the water runs from the water
outlet.
Water line installation kits are available at
extra cost from your dealer.
We recommend using a water line
installation kit that contains copper tubing
and ¼” compression nut.
Connecting to the water supply line
First, shut off the main water
1.
supply.
Locate the nearest cold water drinking line and
2.
install the pipe clamp and shut off valve.
Connect the water line installation kit to the
3.
shut off valve.
Pipe clamp
Pipe clamp
Cold water line
Cold water line
Shut off valve
Shut off valve
3
1
2
3
4
Adjustment
Adjustment
part
part
Fixed part
Fixed part
DA68-02603A.indb 10
DA68-02603A.indb
10
2012.3.15 2:53:50 PM
2012.3.15
2:53:50 PM