Samsung SCD-3080 User Manual - Page 14

Adjust the WDR Sensitivity by selecting LOW, MIDDLE or HIGH.

Get Samsung SCD-3080 PDF manuals and user guides View all Samsung SCD-3080 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Operating Your Camera  HLC (High Light Compensation) : If the scene contains extremely bright light areas such as; from car headlight, the light can mask out much of the on-screen detail. - LEVEL : Adjusts the brightness level of a monitoring area. - LIMIT : Enable to change the operating condition. - MASK COLOR/TONE : Change the color / brightness of the masking area. (Black, Red, Blue, Cyan, Magenta) - TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.  SSDR (Samsung Super Dynamic Range) : SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas. Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas. SSDR ON SSDR OFF WDR : When there are both bright and dark areas at the same time, this mode makes both areas distinctive. < WDR > < OFF > Select 'WDR' to adjust the WDR LIMIT and LEVEL. - LIMIT : Adjust the WDR Sensitivity by selecting LOW, MIDDLE or HIGH. COLOR DOME CAMERA 26 SUD-3080 - LEVEL : Adjust the WDR Brightness by controlling the bar from 1 to 100. - MODE : Indoor and outdoor backlight conditions are appropriately selected. - ANTI ROLLING : Rolling caused around a fluorescent lamp is improved. 3. Select a desired mode using the Function Setup switch. BLC : Adjust the area to be enhanced HLC : Enable the user to change the level, then adjust the level. limit, mask color/tone and area. SSDR : Enable the user to change the level. WDR : Enable the user to change the limit and level. Notes • Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance. • When dark, the HLC is only activated when a bright light exceeding a specific size. (In NIGHT ONLY mode). • The HLC is not activated in day light or when bright light is not present at night. (In NIGHT ONLY mode). • When using the WDR function, the shutter is only available with the fixed(---) mode. • Since the performance of the WDR function may be affected by the area of the bright part of the screen, optimize the installation angle for the best WDR performance. • If you increase LIMIT, the screen display may be distorted. • If you use the VPS (Virtual Progressive Scan) function, the CCD reads differently so you can not use WDR simultaneously. If you set VPS to ON, WDR will be automatically set to FIXED Mode. COLOR DOME CAMERA 27 SUD-3080

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
COLOR DOME CAMERA
SUD-3080
26
COLOR DOME CAMERA
SUD-3080
27
Operating Your Camera
SSDR (Samsung Super Dynamic Range) : SSDR illuminates darker areas of an image
while retaining the same light level for brighter areas to even out the overall
brightness of images with high contrast between bright and dark areas.
Use the Function Setup switch to change the SSDR level in the sub menu according to
the contrast between bright and dark areas.
HLC (High Light Compensation) :
If the scene contains extremely bright light areas such as; from car headlight, the
light can mask out much of the on-screen detail.
- LEVEL : Adjusts the brightness level of a monitoring area.
- LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE :
Change the color / brightness of the masking area.
(Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.
SSDR OFF
SSDR ON
< WDR >
< OFF >
WDR :
When there are both bright and dark areas at the same time, this mode
makes both areas distinctive.
Select ’WDR‘ to adjust the WDR LIMIT and LEVEL.
- LIMIT :
Adjust the WDR Sensitivity by selecting LOW, MIDDLE or HIGH.
3.
Select a desired mode using the Function Setup switch.
BLC :
Adjust the area to be enhanced
then adjust the level.
HLC :
Enable the user to change the level,
limit, mask color/tone and area.
SSDR :
Enable the user to change the
level.
WDR :
Enable the user to change the
limit and level.
•
Because there can be a difference in the effectiveness of HLC according to the amount of
light area in the screen, optimize the installation angle for the best HLC performance.
•
When dark, the HLC is only activated when a bright light exceeding a specific size. (In NIGHT
ONLY mode).
•
The HLC is not activated in day light or when bright light is not present at night. (In NIGHT ONLY mode).
•
When using the WDR function, the shutter is only available with the fixed(---) mode.
•
Since the performance of the WDR function may be affected by the area of the bright part of
the screen, optimize the installation angle for the best WDR performance.
•
If you increase LIMIT, the screen display may be distorted.
•
If you use the VPS (Virtual Progressive Scan) function, the CCD reads differently so you can not
use WDR simultaneously. If you set VPS to ON, WDR will be automatically set to FIXED Mode.
Notes
- LEVEL :
Adjust the WDR Brightness by controlling the bar from 1 to 100.
- MODE : Indoor and outdoor backlight conditions are appropriately selected.
- ANTI ROLLING : Rolling caused around a fluorescent lamp is improved.