Samsung SCD67 User Manual (user Manual) (ver.1.0) (English) - Page 76

Troubleshooting

Get Samsung SCD67 PDF manuals and user guides View all Samsung SCD67 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

ENGLISH Troubleshooting Troubleshooting ✤ Before contacting a service center, perform the following simple checks. They may save you the time and expense of an unnecessary call. Self Diagnosis Display Display 2MIN TAPE END TAPE TAPE C.EMG D.EMG L.EMG R.EMG Blinking slow fast slow no slow slow slow Informs that... the battery pack is almost discharged. the battery pack is fully discharged. When the remaining time of the tape is about 3 minutes. the tape reached its end. there is no tape in camcorder. the tape is protected to record. the camcorder has some mechanical fault. DEW slow moisture condensation has formed in the camcorder. Action Change to a charged one. Change to a charged battery. Prepare a new one. Change to a new one. Insert a tape. If you want to record, release the protection. 1. Eject the tape. 2. Set to OFF. 3. Detach the battery. 4. Reattach the battery. * If unresolved contact your local service representative. see below. Moisture Condensation ✤ If the camcorder is brought directly from a cold place to a warm place, moisture may condense inside the camcorder, on the surface of the tape, or on the lens. In this condition, the tape may stick to the head drum and be damaged or the unit may not operate correctly. To prevent possible damage under these circumstances, the camcorder is fitted with a moisture sensor. ✤ If there is moisture inside the camcorder, "DEW" is displayed. If this happens, none of the functions except cassette ejection will work. Open the cassette compartment and remove the battery. Leave the camcorder for at least two hours in a dry warm room. 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
72
ENGLISH
Troubleshooting
slow
fast
slow
no
slow
slow
slow
slow
the battery pack is almost discharged.
Change to a charged one.
the battery pack is fully discharged.
Change to a charged battery.
When the remaining time of the tape is about 3 minutes.
Prepare a new one.
the tape reached its end.
Change to a new one.
there is no tape in camcorder.
Insert a tape.
the tape is protected to record.
If you want to record, release the protection.
the camcorder has some mechanical fault.
1. Eject the tape.
2. Set to OFF.
3. Detach the battery.
4. Reattach the battery.
* If unresolved contact your local service
representative.
moisture condensation has formed in the camcorder.
see below.
2MIN
TAPE END
TAPE
TAPE
C.EMG
D.EMG
L.EMG
R.EMG
DEW
Display
Blinking
Informs that...
Action
Troubleshooting
Before contacting a service center, perform the following simple checks.
They may save you the time and expense of an unnecessary call.
Self Diagnosis Display
Moisture Condensation
If the camcorder is brought directly from a cold place to a warm place, moisture may condense inside the camcorder, on the surface of the tape,
or on the lens. In this condition, the tape may stick to the head drum and be damaged or the unit may not operate correctly.
To prevent possible damage under these circumstances, the camcorder is fitted with a moisture sensor.
If there is moisture inside the camcorder, “DEW” is displayed.
If this happens, none of the functions except cassette ejection will work.
Open the cassette compartment and remove the battery.
Leave the camcorder for at least two hours in a dry warm room.