Home » Samsung Manuals » Mobile Phones » Samsung SGH-C207 » Manual Viewer

Samsung SGH-C207 User Manual (user Manual) (ver.1.0) (English) - Page 178

Operating Environment, Electronic Devices - user guide

Add to My Manuals
Save this manual to your list of manuals

Page 178 highlights

where no one appears injured, or a vehicle you know to be stolen, call roadside assistance or any other special non-emergency wireless number. Operating Environment Remember to follow any special regulations in force in any area and always switch your phone off whenever it is forbidden to use it, or when it may cause interference or danger. When connecting the phone or any accessory to another device, read its user's guide for detailed safety instructions. Do not connect incompatible products. As with other mobile radio transmitting equipment, users are advised that for the satisfactory operation of the equipment and for the safety of personnel, it is recommended that the equipment should only be used in the normal operating position (held to your ear with the antenna pointing over your shoulder). Electronic Devices Most modern electronic equipment is shielded from radio frequency (RF) signals. However, certain electronic equipment may not be shielded against the RF signals from your wireless phone. Consult the manufacturer to discuss alternatives. Pacemakers Pacemaker manufacturers recommend that a minimum distance of 15 cm (6 inches) be maintained between a wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations Health and Safety Information 177

Section	Page
Intellectual Property	3
Samsung Telecommunications America, L.P.	4
Table of Contents	6
Unpacking	12
Your Phone	14
Phone Layout	14
Display	17
Getting Started	22
Installing the SIM Card	22
1. If necessary, switch off the phone by holding down the key until the power-off image displays.	22
2. Remove the battery. To do so:	22
3. Slide the battery away, as shown.	22
4. Slide the SIM card into the SIM card socket so that it locks the card into place. Make sure the gold contacts of the card face into the phone.	23
5. Place the battery so that the tabs on the end align with the slots at the bottom of the phone.	24
6. Press the battery until it clicks into place. Make sure that the battery is properly installed before switching the phone on.	24
Charging a Battery	24
1. With the battery in position on the phone, plug the connector of the travel adapter into the jack at the bottom of the phone.	25
2. Plug the adapter into a standard AC wall outlet.	25
3. When charging is finished, the battery icon becomes solid and the “Fully charged” message is displayed, unplug the adapter fr...	25
Switching the Phone On/Off	26
1. Press and hold the key until the phone switches on.	26
2. If the phone asks you to enter the phone password, enter the password and press the OK soft key. The phone password is factory set to “00000000.” For further details, see “Change Password” on page 157.	26
3. If the phone asks for a PIN, enter the PIN and press the OK soft key or key. For further details, see “Change PIN” on page 157.	27
4. When you wish to switch the phone off, press and hold the key until the power-off image displays.	27
Call Functions	28
Making a Call	28
1. Press and hold the key. The + character appears.	28
2. Enter the country code, area code, and phone number and press the key.	28
1. If you have typed characters on the display, press the key to return to Idle mode.	29
2. Press the key to display a list of the last numbers in the order you made or received.	29
3. Use the Up and Down keys or volume keys to scroll through the numbers until the number you want highlights.	30
Adjusting the Volume	30
Answering a Call	31
1. Press the key or the Accept soft key to answer the incoming call.	31
2. End the call by pressing the key.	32
Viewing Missed Calls	32
1. Press the View soft key.	32
1. Press the Options soft key or key.	32
2. Press the Up or Down key to highlight the Edit option.	32
3. Press the Select soft key or key.	33
4. Change the number.	33
1. Press the Options soft key or key.	33
2. If necessary, press the Up or Down key to highlight the Delete option.	33
3. Press the Select soft key or key.	33
Quickly Switching to Silent Mode	33
Selecting Functions and Options	36
1. Press the appropriate soft key.	37
Locking or Unlocking the Keypad	38
Phone Book	40
Storing a Number with a Name	40
1. Enter the number you want to store.	40
2. To save the number, press the Save soft key or key.	40
3. Select an icon to identify the category of the number to be stored. Three categories are available:	40
4. Choose either SIM Memory or Phone Memory to store the number.	41
5. Enter a name and press the OK soft key or key.	41
6. Press the OK soft key to store the name and number. The new Phone Book entry displays.	41
1. At the idle screen, press the Name soft key.	41
2. Scroll to New Entry by pressing the Up or Down key and press the Select soft key.	41
3. Select an icon to identify the category of the number to be stored by pressing the Left or Right key, and press the Select soft key or key.	41
4. Choose either SIM Memory or Phone Memory to store the number. Press the Select soft key or key.	42
5. Enter a name and press the OK soft key or key.	42
6. Enter a number or address you want to store and press the Save soft key or key.	42
7. Press the OK soft key or key.	42
Using Phone Book Entry Options	42
Dialling a number from Phone Book	43
1. In Idle mode, enter the location number for the phone number you want to dial and press the key.	43
2. You can press the Up or Down key to find other numbers on the list.	43
3. Press the Dial soft key, key, or key when you have selected the number you want.	44
1. In Idle mode, press and hold the 0 key. A + appears.	44
2. Enter the location number of the phone number you want and press the key.	44
3. The list of entries in the phone’s memory appears.	44
4. You can press the Up or Down key to find other numbers on the list.	44
5. Press the Dial soft key, key, or key when you have selected the number you want.	44
Searching for a Number in Phone Book	44
1. At the idle screen, press the Name soft key.	44
2. Press the Select soft key or key when Search highlights. You are asked to enter a name.	44
3. Enter the first few letters of the name.	44
4. Once you have found the entry, press the key to dial the number, or press the Options soft key or key to access the Phone Book entry options; for further details, see page 41.	45
1. When the idle screen displays, press the Name soft key.	45
2. Scroll to Group Search by pressing the Up or Down key and press the Select soft key. You are asked to enter a group name.	45
3. Enter the first few letters of the group name that you wish to find.	45
4. Scroll to the group you want by pressing the Up or Down key and press the View soft key or key.	46
5. Once you have found the entry, press the key to dial the number, or press the Options soft key or key to access the Phone Book entry options; for further details, see page 41.	46
Editing a Caller Group	46
1. When the idle screen displays, press the Name soft key.	46
2. Scroll to Group Edit by pressing the Up or Down key and press the Select soft key or key.	46
3. Scroll through the group list by pressing the Up or Down key.	46
4. When the group you want highlights, press the Options soft key or key.	46
5. Select each option and change the settings, as required. The following options are available:	46
6. When you are finished, press the or key.	47
Deleting all of the Phone Book entries	47
1. When the idle screen displays, press the Name soft key.	47
2. Scroll to Delete all by pressing the Up or Down key and press the Select soft key or key.	47
3. To place a check mark by the memory location you want to empty, All, SIM memory, or Phone memory, press the key.	47
4. Press the Delete soft key to delete the entries in the selected memory location.	47
5. Enter the phone password and press the OK soft key or key.	47
6. When the confirmation message appears, press the Yes soft key or key.	48
7. When you are finished, press the C or key.	48
Speed-dialing	48
1. At the idle screen, press the Name soft key.	48
2. Scroll to Speed Dial by pressing the Up or Down key and press the Select soft key or key.	48
3. Select the key to which you wish to assign the speed- dialing number, from the to keys, and press the OK soft key or key.	48
4. Select a Phone Book entry and press the View soft key or key.	48
5. Select a number if the entry has more than one number, by pressing the Up or Down key and press the Select soft key or key.	49
6. Once you have assigned a number to the selected key, you can use the following options by pressing the Options soft key or key:	49
7. When you are finished, press the or key.	49
Checking the Memory Status	49
1. When the idle screen displays, press the Name soft key.	49
2. Select the Memory Status option.	49
3. Press the Up or Down key to view the number of existing and remaining entries in the SIM card and phone’s memory.	50
4. When you are finished, press the or key.	50
Using the service Dialing Numbers	50
1. When the idle screen displays, press the Name soft key.	50
2. Select the SDN option by pressing the Up or Down key and press the Select soft key or key.	50
3. To dial the number displayed, press the Dial soft key, key, or key.	50
Entering Text	52
Changing the Text Input Mode	53
Using T9 Mode	54
1. When you are in T9 mode, start entering a word by pressing the to keys. Press each key only once for each letter.	54
2. Enter the whole word before editing or deleting the keystrokes.	54
3. When the word displays correctly, go to step 4.	54
4. Put a space by pressing the key and start entering the next word.	54
1. After pressing the keys corresponding to the word you want to add, press the 0 key or Up or Down key to display the alternative words.	55
2. When you press the 0 key or Up or Down key at the last alternative word, the display shows Add on the bottom line. Press the Add soft key or key.	55
3. If necessary, clear the word using the C key and enter the word you want to add using Alphabet mode. See page 55.	55
4. Press the OK soft key or key.	55
5. The word is added to the T9 dictionary and becomes the first word for the associated keypress series.	55
Using the Upper/Lower-Case Character Mode	56
1. Press the key labeled with the letter you want:	56
2. Select the other letters in the same way.	56
Using Number Mode	57
Using Symbol Mode	58
Options During a Call	60
Putting a Call on Hold	60
1. Enter the phone number that you wish to dial or look it up in Phone Book.	60
2. Press the key to dial the second call.	60
1. Put the current call on hold by pressing the Hold soft key.	60
2. Make the second call in the normal way.	60
Using the Menu Functions	61
1. Press the Options soft key.	61
2. Press the OK soft key when the Menu option highlights.	61
3. Press the Up or Down key to scroll through the menu list.	61
4. When the menu you want highlights, press the Select soft key.	61
5. If the selected menu has sub-options, repeat steps 3 and 4.	61
Switching the Microphone Off (Mute)	61
1. Press the Options soft key.	61
2. If necessary, press the Down key to highlight the Mute option.	61
3. Press the OK soft key or key. The other person can no longer hear you.	62
1. Press the Options soft key.	62
2. If necessary, press the Down key to highlight the Unmute option.	62
3. Press the OK soft key or key. The other person can hear you again.	62
Muting/Sending Key Tones	62
Sending Tones	62
1. Press the Options soft key.	62
2. Highlight the Send DTMF option.	62
3. Press the OK soft key or key.	62
4. Enter the required number and press the OK soft key or key.	62
Searching for a Number in Phone Book	63
1. Press the Options soft key.	63
2. Press the Down key to highlight the Phone Book option.	63
3. Press the OK soft key or key.	63
4. Enter the name that you wish to find.	63
5. To view the highlighted entry, press the View soft key or key.	63
Call Waiting	63
1. Press the key to answer the incoming call. The first call is automatically put on hold.	63
2. To switch between the two calls, press the Swap soft key.	64
3. To end a call on hold, press the Options soft key and select the End Held Call option.	64
4. To end the current call, press the key.	64
Making a Multi-party Call	64
1. Call the first participant in the normal way.	64
2. Call the second participant in the normal way. The first call is automatically put on hold.	64
3. To join the first participant to the multi-party call, press the Options soft key and select Join. Press the OK soft key or key.	64
4. To add a new person to the multi-party call, call the person in the normal way and then press the Options soft key. Select the Join option and press the OK soft key.	64
1. Press the Options soft key and choose the Select one option. Press the OK soft key.	65
2. Highlight a person by pressing the Up or Down key, and press the Select soft key or the key or key.	65
3. When the Private option highlights, press the OK soft key or key.	65
4. To return to the multi-party call, press the Options soft key and select Join. Press the OK soft key or key.	65
1. Press the Options soft key and choose the Select one option. Press the OK soft key or key.	65
2. Highlight a person by pressing the Up or Down key, and press the Select soft key or the key or key.	65
3. Press the Down key to select the Remove option and press the OK soft key or key.	65
4. When you want to end the multi-party call, press the key.	66
Using the Menus	68
Accessing a Menu Function by Scrolling	68
1. In Idle mode, press the Menu soft key.	68
2. Scroll using the Up and Down keys to reach a main menu, Phone Settings for example. Press the Select soft key or key to enter the menu.	68
3. If the menu contains sub-menus, Language for example, you can access them by scrolling and pressing the Select soft key or key.	68
Accessing a Menu Function by Using Its Shortcut	69
1. Press the Menu soft key.	69
2. Press the key for Phone Settings.	69
3. Press the key for Language.	69
List of Menu Functions	69
Recent Calls	76
Missed Calls	76
Calls Received	76
Calls Made	76
Voice Mail	77
Delete All	78
Call Time	78
Messaging	80
Text Messages	80
1. Create your message.	81
2. When you finish entering your message, press the Options soft key or key. The following options are available:	81
3. Select Send or Save and Send, and press the Select soft key or key.	81
4. If you select a save option, select a location and press the OK soft key or key.	81
5. Enter a destination number and press the OK soft key or key. The message is sent.	81
1. Create your message.	82
2. Press the Options soft key or key.	82
3. Select one of the following options by using the Up and Down keys and pressing the Select soft key or key.	82
4. Complete the message, and send or save it by following the procedure from step 2 on page 80.	83
1. Select a message from the list and press the View soft key or key to read the message contents.	83
2. To scroll through the contents, press the Up or Down key.	83
3. To scroll to the previous message press the key or press the key for the next message.	83
1. Select a message from the list and press the View soft key or key to read the message contents.	84
2. To scroll through the contents, press the Up or Down key.	84
3. To scroll to the previous message press the key or press the key for the next message.	84
Multimedia Messages	90
1. Enter the subject of your message and press the OK soft key or key.	91
2. When Add Here highlights, press the Options soft key or key and add the message contents using one of the following options:	91
3. Repeat step 2 until you have finished creating your message.	92
4. If you want to change the added items, press the Up or Down key to highlight one and press the Options soft key or key.	92
5. When you have finished creating the message, choose Send and press the Select soft key or key.	93
6. Select a destination type, To, Cc, or Bcc, and press the Select soft key or key.	93
7. Choose one of the following options and press the Select soft key or key:	93
8. Enter a number or an e-mail address, or select a number from Phone Book.	93
9. When the correct number or address displays, press the OK soft key or key.	93
10. To add a destination, press the Select soft key or key when Add destination highlights. Repeat from step 7.	93
11. To enter additional numbers or addresses to the other destination types, press the C key or the key and repeat steps 6 through 10.	94
12. When you have finished entering the destinations, select Send message and press the Select soft key or key.	94
1. Press the View soft key or key to view the message.	94
2. To scroll through the message information, press the Up or Down key.	94
3. To read the message, press the Select soft key or key when Retrieve is highlighted.	95
4. To scroll through the message, press the Up or Down key.	96
1. Select a message on the list and press the Select soft key or key.	96
2. Press the OK soft key or key to go to the message view screen.	96
3. To scroll through the message, press the Up or Down key.	96
4. To scroll to the previous or next message, press the or key.	97
1. Select a message and press the Select soft key or key to view the message contents.	98
2. Press the OK soft key or key to go to the message view screen.	98
3. To scroll through the message, press the Up or Down key.	98
4. To scroll to the previous or next message, press the or key.	98
1. Scroll through the template list using the Up and Down keys.	99
2. When the message template you want highlights, press the Select soft key or key.	99
3. Press the OK soft key or key to access the following options, or the display automatically shows the options after a specified time:	99
Instant Messaging (IM)	103
1. Highlight IM (Menu 2.3) and press the Select soft key.	103
2. Use the navigation keys to highlight the AIM. Press the Select soft key.	103
3. Enter your Screen name and Password. Press the Sign on soft key.	104
4. If the sign-on was successful, you will see Welcome, followed by a list of options.	104
Send an Instant Message	104
1. From the AIM main menu, scroll to and select Buddy List.	104
2. Use the navigation keys to highlight a buddy and press the Select soft key or key.	104
Conversations	105
Blocked List	105
Saved history	105
Sign Off	106
1. Scroll right on the navigation key to highlight the ICQ icon. Press the Select soft key or key.	107
2. Enter your ICQ number and Password. Press the Connect soft key. The Contact List screen displays with the My Status option highlighted.	107
3. Press the Select soft key. The following options are displayed.	107
Conversations	108
Blocked List	108
Saved history	108
Disconnect	108
Push Message	109
Network Services	110
Call Forwarding	110
1. Select a call forwarding option by pressing the Up or Down key and then press the Select soft key or key.	110
2. Select the type of calls, voice or data, by pressing the Up or Down key and then press the Select soft key or key.	110
3. Enter the number to which the calls are to be forwarded and press the OK soft key or key.	111
Call Barring	111
To Set Your Call Barring Options	112
1. Select a call barring option by pressing the Up or Down key and then press the Select soft key or key.	112
2. Select the type of calls, voice or data, by pressing the Up or Down key and then press the Select soft key or key.	112
3. Press the Activate soft key to confirm your settings.	112
4. Enter your call barring password supplied by your service provider.	112
To Deactivate Specific Call Barring Settings	112
1. Select the call barring option to be deactivated.	112
2. Select the type of calls to which this option applies.	112
3. Press the Deactivate soft key.	112
4. Enter your call barring password supplied by your service provider.	113
Call Waiting	113
1. Select the type of calls, voice or data, to which the call waiting option is to be applied by pressing the Up or Down key and then press the Select soft key or key.	113
2. You can activate or deactivate the call waiting feature using the Activate or Deactivate soft key respectively.	113
Network Selection	114
1. When Network Selection displays, press the Select soft key.	114
2. Press the Up or Down key until the appropriate option highlights, then press the OK soft key or key.	114
3. Press the Up or Down key until the network you want highlights and then press the OK soft key or key.	114
Caller ID	114
Closed User Group (CUG)	115
Games	118
Downloading a new game	118
Launching a MIDlet	118
1. Scroll to the MIDlet you want on the Games list and press the Launch soft key or key.	118
2. On the startup screen of the MIDlet, scroll to an option using the Navigation keys.	118
3. Press the key to confirm your selection.	119
Using the game options	119
MEdia Mall	122
Shop Ringtones	122
1. Use the Select soft key to choose the option.	122
2. Use the Up and Down navigation keys to move to your desired option and press the Select soft key.	122
3. Continue to navigate through the menu options.	122
Shop Games	122
1. Use the Select soft key to choose the option.	122
2. Use the Up and Down navigation keys to move to your desired option and press the Select soft key.	122
3. Continue to navigate through the menu options.	122
Shop Graphics	123
1. Use the Select soft key to choose the option.	123
2. Use the Up and Down navigation keys to move to your desired option and press the Select soft key.	123
3. Continue to navigate through the menu options.	123
Shop Multimedia	123
1. Use the Select soft key to choose the option.	123
2. Use the Up and Down navigation keys to move to your desired option and press the Select soft key.	123
3. Continue to navigate through the menu options.	123
Shop Applications	123
1. Use the Up and Down navigation keys to move to your selection and press the Options soft key. Press the Select soft key to continue or Back to make another selection.	123
2. Use the Up and Down navigation keys to move to your desired option and press the Select soft key.	124
3. Continue to navigate through the menu options.	124
MEdia Home	124
1. Use the Select soft key to choose the option.	124
2. Use the Up and Down navigation keys to move to your desired option and press the Select soft key.	124
3. Continue to navigate through the menu options.	124
Sound Settings	126
Ring Tone	126
Ring Volume	126
Shop Ringtones	126
Alert Type	127
Keypad Tone	127
Message Tone	127
Alert on Call	128
Power On/Off	128
Extra Tones	129
Applications	130
Alarm	130
1. Choose the type of alarm to be set and press the Select soft key or key.	130
2. Enter the time for the alarm to sound.	130
3. Press the OK soft key.	131
4. Choose AM or PM using the Up and Down keys and press the Select soft key or key.	131
5. If you select Wake-up Call in step 1, select the repeat option, Monday to Friday or Monday to Saturday and press the Select soft key or key.	131
Calendar	131
1. Select a date on the calendar, using the Navigation keys.	132
2. Press the key.	132
3. Enter your memo and then press the OK soft key or key.	132
4. If you want the alarm to ring on the chosen day, press the Yes soft key or key.	132
5. If you pressed the Yes soft key or key, set the time for the alarm and press the OK soft key or key.	133
6. Select either AM or PM and press the Select soft key or key.	133
Time & Date	134
1. Select the city corresponding to your time zone by pressing the Left or Right key one or more times. The local date and time display.	134
2. Press the Set soft key.	134
Calculator	135
1. Enter the first number using the numeric keys.	135
2. Press the right soft key until the symbol you want displays: + (addition), - (subtraction), * (multiplication), / (division).	135
3. Enter the second number.	135
4. To view the result, press the key.	135
5. Repeat steps 1 to 4 as many times as required.	135
To Do List	135
1. Press the New soft key or key.	135
2. Enter the first task.	136
3. Press the OK soft key or key.	136
4. Select a priority level of high, normal, or low priority using the Up or Down key and press the Select soft key or key.	136
5. Enter your deadline and press the OK soft key or key.	136
1. Highlight the task.	137
2. Press the Options soft key.	137
3. Scroll through the tasks using the Up and Down keys.	137
1. Highlight the task.	138
2. Press the key to mark the task as completed as of the current date and time. Or	138
1. Highlight the task.	138
2. Press the Options soft key.	138
3. Select the Mark option.	138
4. Select the appropriate status (Done or Undo).	138
1. Press the Options soft key.	138
2. Select the New option.	138
3. Enter text, priority and deadline for the task.	138
1. Highlight the task.	139
2. Press the Options soft key.	139
3. Select the Edit option.	139
4. Change the text, priority and/or deadline for the task.	139
1. Press the Options soft key.	139
2. Select the Sort option.	139
3. Select the sort criterion (High, Low, Done or Undo).	139
1. Highlight the task.	139
2. Press the Options soft key.	139
3. Select the Copy option.	139
4. Change the text, priority and/or deadline for the task.	139
1. Highlight the task.	140
2. Press the Options soft key.	140
3. Select the Copy to Calendar option.	140
4. Change the text and/or deadline for the task and set the alarm.	140
1. Highlight the task.	140
2. Press the Options soft key.	140
3. Select the Delete option.	140
1. Press the Options soft key.	140
2. Select the Delete All option.	140
3. Confirm the deletion by pressing the OK soft key.	140
1. Press the Options soft key.	140
2. Select the Exit option.	140
Voice Memo	141
1. To start recording, press the Record soft key or key.	141
2. Record a memo by speaking into the microphone.	141
3. When you press the Stop soft key or key, or if the recording time expires, the following options display:	141
4. To save the memo, choose Save and press the Select soft key or key.	141
5. Press the C key to clear the default name, if necessary, and enter a name for the memo.	141
6. Press the OK soft key or key.	142
7. Press the Options soft key or key to access the following memo options:	142
8. To exit, press the soft key or key.	142
Currency Exchange	143
1. Enter the current exchange rate of your source currency and press the OK soft key.	143
2. Enter the amount to convert and press the OK soft key.	143
3. Press the soft key to exit the currency converter.	143
My MEdia	144
MEdia Net	144
Exiting the WAP Browser	144
Navigating the WAP Browser	145
Entering Text in the WAP Browser	145
1. Set the cursor to the right of the character(s) to be corrected.	146
2. Press the key as required.	146
3. Enter the correct character(s).	146
Selecting and Using Menu Options	146
1. Press and hold down the key. A menu displays.	146
2. Highlight a menu by pressing the Up and Down keys.	146
3. Select the option by pressing the Select soft key or key.	146
4. If necessary, select a secondary option using the Up and Down keys, and press the Select soft key or key to confirm.	146
1. Select an empty location and press the Options soft key or key.	148
2. Enter the address and press the Enter soft key or key.	148
3. Enter a name for the favorite item and press the Enter soft key.	148
Audio	150
Graphics	150
Delete All	151
Memory Status	152
Phone Settings	154
Display Settings	154
1. Use the Up or Down key to select the image you want, then press the Select soft key or key.	154
2. When the image displays, press the Select soft key or key.	154
3. To choose the color of the text select the Text Color option and select the color of the text to be displayed on the idle screen.	154
Greeting Message	156
Own Number	156
Language	157
Security	157
Extra Settings	160
Short Cut	161
1. Select the key to be used as a shortcut key by pressing the Up or Down key, and press the Select soft key.	161
2. Select the menu to be assigned to the key by pressing the Up or Down key.	162
3. Press the Select soft key or key to save the selection.	162
Reset Settings	162
1. Select the Reset Settings menu.	162
2. Enter the 8-digit password and press the OK soft key.	162
TTY Settings	162
1. From the menu screen select Phone Settings (Menu 9).	163
2. Press the 9 key to access this function.	163
3. Enter 4-T-T-Y or (4889) in the password field and press the OK soft key.	163
Solving Problems	164
Access Codes	168
Phone Password	168
PIN	169
PUK	169
1. Enter the PUK and press the OK soft key or key.	169
2. Enter a PIN of your choice and press the OK soft key or key.	169
3. When the Confirm New PIN message displays, enter the same code again and press the OK soft key or key.	169
PIN2	170
PUK2	170
1. Enter the PUK2 and press the OK soft key or key.	170
2. Enter a new PIN2 of your choice and press the OK soft key or key.	170
3. When the Confirm PIN2 message displays, enter the same code again and press the OK soft key or key.	170
Health and Safety Information	172
Exposure to Radio Frequency (RF) Signals	172
For Body Operation	174
Precautions When Using Batteries	175
Road Safety	176
1. Get to know your wireless phone and its features, such as speed dial and redial. If available, these features help you to place your call without taking your attention off the road.	176
2. When available, use a hands-free device. If possible, add an extra layer of convenience and safety to your wireless phone with one of the many hands-free accessories available today.	176
3. Position your wireless phone within easy reach. Be able to access your wireless phone without removing your eyes from the road. If you get an incoming call at an inconvenient time, let your voice mail answer it for you.	176
4. Let the person you are speaking with know you are driving; if necessary, suspend the call in heavy traffic or hazardous weather conditions. Rain, sleet, snow, ice and even heavy traffic can be hazardous.	176
5. Do not take notes or look up phone numbers while driving. Jotting down a To Do list or flipping through your phone book takes your attention away from your primary responsibility, driving safely.	177
6. Dial sensibly and assess the traffic; if possible, place calls when you are not moving or before pulling into traffic. Try to...	177
7. Do not engage in stressful or emotional conversations that may be distracting. Make the people with whom you are talking aware that you are driving and suspend conversations that have the potential to divert your attention from the road.	177
8. Use your wireless phone to call for help. Dial the emergency number in the case of fire, traffic accident or medical emergencies. Remember, it is a free call on your wireless phone!	177
9. Use your wireless phone to help others in emergencies. If you see a car accident, crime in progress or other serious emergency where lives are in danger, call the emergency number, as you would want others to do for you.	177
10. If you see a broken-down vehicle posing no serious hazard, a broken traffic signal, a minor traffic accident where no one ap...	177
Operating Environment	178
Electronic Devices	178
Potentially Explosive Environments	180
Emergency Calls	180
1. If the phone is not on, switch it on.	181
2. Key in the emergency number for your present location (for example, 911 or other official emergency number). Emergency numbers vary by location.	181
3. Press the key.	181
Other Important Safety Information	181
Care and Maintenance	182
Acknowledging Special Precautions and the FCC and Industry Canada Notice	183
1. This device may not cause harmful interference, and	184
2. This device must accept any interference received.	184
Appendix A: CERTIFICATION INFORMATION (SAR)	186
Appendix B: Guide to Safe and Responsible Wireless Phone Use	188
Wireless Phone “Safety Tips”	189
1. Get to know your wireless phone and its features such as speed dial and redial. Carefully read your instruction manual and le...	189
2. When available, use a hands free device. A number of hands free wireless phone accessories are readily available today. Wheth...	189
3. Position your wireless phone within easy reach. Make sure you place your wireless phone within easy reach and where you can g...	189
4. Suspend conversations during hazardous driving conditions or situations. Let the person you are speaking with know you are dr...	190
5. Do not take notes or look up phone numbers while driving. If you are reading an address book or business card, or writing a “...	190
6. Dial sensibly and assess the traffic; if possible, place calls when you are not moving or before pulling into traffic. Try to...	190
7. Do not engage in stressful or emotional conversations that may be distracting. Stressful or emotional conversations and drivi...	190
8. Use your wireless phone to call for help. Your wireless phone is one of the greatest tools you can own to protect yourself an...	191
9. Use your wireless phone to help others in emergencies. Your wireless phone provides you a perfect opportunity to be a “Good S...	191