Samsung SP-D400 User Manual (user Manual) (ver.1.0) (English) - Page 11

abnormally or after

Get Samsung SP-D400 PDF manuals and user guides View all Samsung SP-D400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Action 2 Action 3 Action 4 Action 5 Action 6 When the lamp cover protecting the lamp unit is not properly closed or the sensor system is not in normal operating condition. When temperature inside of the projector becomes too high. When the color wheel fails to operate. The lamp malfunctions after power turns off abnormally or after powering on right after turning off the projector. When the screen becomes darker Check whether the screws at the bottom side of the projector are fastened correctly. If they are abnormally fastened, contact your product distributor or service center. Adjust the installation state of your projector by referring to the Installation Precautions section listed above. Cool down your projector sufficiently and then operate it again. If the same problem occurs continually, contact your product distributor or service center. Disconnect and reconnect the power cord and start the projector again. If the same symptom still occurs, contact your product distributor or service center. Turn the power off, wait for a sufficient amount of cooling time and then turn the power on to operate. If the same problem occurs continually, contact your product distributor or service center. Check the lamp usage time on the Information Display screen. If you need to replace the lamp, contact your product distributor or service center. This Projector uses a cooling fan system to keep the unit from overheating. Operation of the cooling fan may cause noise, which does not affect the product performance and is part of normal operation. Rear Side 1. RS-232C port (For service input terminals) 6. HDMI/DVI IN Input port 2. SERVICE Input port 7. PC OUT terminal 3. VIDEO IN Input port 8. PC IN Input port

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
¹ction 2
¶hen the lamp cover
protecting the lamp unit is
not properly closed or the
sensor system is not in
normal operating
condition.
Àheck whether the screws at the bottom side of the projector are
fastened correctly. µf they are abnormally fastened, contact your
product distributor or
service center
.
¹ction 3
¶hen temperature inside
of the projector becomes
too high.
¹djust the installation state of your projector by referring to the
µnstallation ºrecautions section listed above. Àool down your
projector sufficiently and then operate it again. µf the same problem
occurs continually, contact your product distributor or
service center
.
¹ction 4
¶hen the color wheel fails to
operate.
·isconnect and reconnect the power cord and start the projector
again. µf the same symptom still occurs, contact your product
distributor or
service center
.
¹ction 5
The lamp
malfunctions after power
turns off
abnormally or after
powering on right after
turning off the projector.
Turn the power off, wait for a sufficient amount of cooling time and
then turn the power on to operate. µf the same problem occurs
continually, contact your product distributor or
service center
.
¹ction 6
¶hen the screen becomes
darker
Àheck the lamp usage time on the µnformation ·isplay screen. µf you
need to replace the lamp, contact your product distributor or
service
center
.
This ºrojector uses a cooling fan system to keep the unit from overheating. »peration of the cooling fan may
cause noise, which does not affect the product performance and is part of normal operation.
¼ear ¿ide
1. ¼¿-232À port (For service input terminals)
2. ¿½¼VµÀ½ µnput port
3. Vµ·½» µ¾ µnput port
6. H·Mµ/·Vµ µ¾ µnput port
7. ºÀ »¸T terminal
8. ºÀ µ¾ µnput port