Samsung WA45H7000AW/A2 User Manual Ver.1.0 (English, French, Spanish) - Page 16

STEP 4, Powering your washer, Running a test cycle, Calibration mode - display show 0 at end of cycle

Get Samsung WA45H7000AW/A2 PDF manuals and user guides View all Samsung WA45H7000AW/A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

installing your washer STEP 4 Powering your washer Plug the power cord into a 3-prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded electrical outlet. Test run Make sure that you install your washing machine correctly by running the Rinse+Spin cycle after the installation is complete. STEP 5 Running a test cycle Run a test cycle as follows to check if your washer is properly installed. 1. Load about 6 pounds of laundry into the tub. 2. Press the Power button to turn on your washer. 3. Select the Rinse+Spin cycle by turning the Cycle Selector. 4. Press the Start/Pause button to start the test cycle. 5. The washer should not rock or vibrate excessively when water is supplied or when washing or spinning, and should drain well during the spin cycle. If water leaks while water is being supplied or drained, check the water connections. Refer to the "Connecting the water and the drain" section on pages 14~15 for instructions. If the washer rocks and vibrates excessively, level your washer again. Refer to the "Leveling your washer" section on page 15 for instructions. STEP 6 Calibration mode Your Samsung washing machine detects the laundry weight automatically. For more accurate weight detection, please run Calibration Mode after the installation. To run Calibration Mode, follow these steps: 1. Remove laundry or any contents in the machine. 2. Press the Temp. and Delay End buttons simultaneously, and then press the Power button. The machine turns on. 3. Press the Start/Pause button to activate "Calibration Mode". 4. The pulsator rotates clockwise and counterclockwise for approximately 1 minute. 5. When "Calibration Mode" is finished, "End" (WA48H7400A*, WA45H7200A*) / "0" (WA45H7000A*) appears on the display, and the machine automatically turns off. The washing machine is now ready for use. English - 16 8")"8"4)@8")@64&3."/6 1@&/JOEE

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
English -
16
STEP 4
Powering your washer
Plug the power cord into a 3-prong, well grounded 120 volt 60
Hz approved electrical outlet protected by a 15-amp fuse or
comparable circuit breaker.
Your washer is grounded through the third prong of the power
cord when plugged into a three-prong grounded electrical
outlet.
Test run
Make sure that you install your washing machine correctly by running the
Rinse+Spin
cycle
after the installation is complete.
STEP 5
Running a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1.
Load about 6 pounds of laundry into the tub.
2.
Press the
Power
button to turn on your washer.
3.
Select the Rinse+Spin cycle by turning the
Cycle Selector
.
4.
Press the
Start/Pause
button to start the test cycle.
5.
The washer should not rock or vibrate excessively when water is supplied or when washing
or spinning, and should drain well during the spin cycle.
If water leaks while water is being supplied or drained, check the water connections. Refer
to the “Connecting the water and the drain” section on pages 14
~
15 for instructions.
If the washer rocks and vibrates excessively, level your washer again. Refer to the “Leveling
your washer” section on page 15 for instructions.
STEP 6
Calibration mode
Your Samsung washing machine detects the laundry weight automatically.
For more accurate weight detection, please run Calibration Mode after the installation.
To run Calibration Mode, follow these steps:
1.
Remove laundry or any contents in the machine.
2.
Press the Temp. and Delay End buttons simultaneously, and then press the Power button.
The machine turns on.
3.
Press the
Start/Pause
button to activate “Calibration Mode”.
4.
The pulsator rotates clockwise and counterclockwise for approximately 1 minute.
5.
When “Calibration Mode” is finished, “End” (WA48H7400A*, WA45H7200A*) / “0”
(WA45H7000A*)
appears on the display, and the machine automatically turns off. The washing machine is now
ready for use.
installing your washer
WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-01_EN.indd
16
2014-1-10
15:41:47