Samsung WA484DSHAWR/A1 User Manual Ver.1.0 (English, French, Spanish) - Page 17

Connecting the drain hose

Get Samsung WA484DSHAWR/A1 PDF manuals and user guides View all Samsung WA484DSHAWR/A1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

01 installing your washer 5. Tighten the fitting by hand until it is snug, then make two-thirds of a turn with a wrench. To ensure the correct water usage, connect both the HOT and COLD water faucets. If either or both are not connected, an "nF" (no fill) error can occur. Check if the water supply hose is not twisted or bent. If the CAUTION hose is twisted or bent, there is a danger of a water leakage and electric shock due to the water leakage. 6. Turn on the HOT and COLD water supplies and check all the water supply intake connections and the faucets for water leaks. Connecting the drain hose Drain can be installed using method you need. 1. floor standpipe - Minimum diameter for a standpipe drain: 2" (51 mm). - Minimum carry-away capacity: 17 gal. (64 Liter) per minute. - Top of standpipe must be at least 39" (990 mm) high, install no higher than 96" (2.4 m) from bottom of washer. 4" (100 mm) Stand pipe Hose retainer Tie strap 39" Min (99 cm) - If you must install higher than 96" (2.4 m), you will need a sump pump system. 2. laundry tub. - Minimum capacity: 20 gal. (76 Liter). - Top of laundry tub must be at least 39" (990 mm) above floor. - Install no higher than 96" (2.4 m) from bottom of washer. 96" Max 39" Min 4" (100 mm) Hose retainer Tie strap 3. Over the edge of a wash basin - Secure the guide to the side of the basin wall with a hook or to the tap with a piece of string to prevent the drain hose from moving. Make sure that the connection between the drain hose and the standpipe is not airtight. WA484DSHA-03050D_EN.indd Sec3:17 installing your washer _17 2012-07-02 3:39:20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
installing your washer
_17
5.
Tighten the fitting by hand until it is snug, then make two-thirds of a
turn with a wrench.
To ensure the correct water usage, connect both the HOT and
COLD water faucets. If either or both are not connected, an
“nF” (no fill) error can occur.
Check if the water supply hose is not twisted or bent. If the
hose is twisted or bent, there is a danger of a water leakage and
electric shock due to the water leakage.
6.
Turn on the HOT and COLD water supplies and check all the water supply intake
connections and the faucets for water leaks.
Connecting the drain hose
Drain can be installed using method you need.
1.
floor standpipe
-
Minimum diameter for a standpipe drain: 2” (51 mm).
-
Minimum carry-away capacity: 17 gal. (64 Liter) per
minute.
-
Top of standpipe must be at least 39” (990 mm) high, install
no higher than 96” (2.4 m) from bottom of washer.
-
If you must install higher than 96” (2.4 m), you will need a
sump pump system.
2.
laundry tub.
-
Minimum capacity: 20 gal. (76 Liter).
-
Top of laundry tub must be at least 39” (990 mm) above floor.
-
Install no higher than 96” (2.4 m) from bottom of washer.
3.
Over the edge of a wash basin
-
Secure the guide to the side of the basin wall with a
hook or to the tap with a piece of string to prevent the
drain hose from moving.
Make sure that the connection between the drain hose
and the standpipe is not airtight.
01 installing your washer
CAUTION
96” Max
39” Min
4”
(100 mm)
Hose
retainer
Tie strap
Stand pipe
39” Min
(99 cm)
Tie strap
Hose retainer
4”
(100 mm)
WA484DSHA-03050D_EN.indd Sec3:17
WA484DSHA-03050D_EN.indd
Sec3:17
2012-07-02
3:39:20
2012-07-02
3:39:20