Samsung WA48H7400AP/A2 Trouble Shooting Guide Tech Manual (English, French, Sp - Page 7

Service Mode, Quick Spin Test Mode, WARNING

Page 7 highlights

ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. Service Mode Delay End + Pre Soak Service Mode: 1. The washer must be on to go into the Service Mode. 2. The motor speed will be displayed when started (It displays 0 when the motor does not spin). 3. The present state of the machine will not be changed. (i.e., the current cycle in progress will not be interrupted and only the display will change) 4. To exit Service Mode, press Delay End and Pre Soak Key for 3 second again, or Power Key.If no key is operated during Service Mode for 5 minutes, the machine will return to normal user mode. Quick Spin Test Mode Delay End + Self Clean While it is not in Hold Speed Mode Delay End + Self Clean 3 sec While a cycle is not running Delay End + Self Clean for 3 sec or after 10 minutes Definition of Quick Spin Test Mode: - Quick Spin Test Mode is to do Spin Check. (High RPM) How to Enter: - During Service Mode, press the Delay End and Self Clean Key for 3 seconds to enter Quick Spin Test Mode. - Cannot enter once the washing cycle has started. Quick Spin Test Mode: As it enters into the Quick Spin Test Mode, it starts spinning and reaches its maximum RPM. Once the Spin speed reaches the maximum RPM, the speed drops immediately. To hold Quick Spin Test Mode (entering Hold Speed Mode), press the Start/Pause button. If the Start/Pause button is pressed during Quick Spin Test Mode, it will stop accelerating and hold its spinning speed for 10 minutes before going back to Quick Spin Test Mode. Also, to cancel the hold and allow Quick Spin Test Mode to continue, press the Delay End and Self Clean Key together for 3 seconds. If you hold down the Delay End and Self Clean key for three (3) seconds when the washing machine is not in Hold Speed Mode, Quick Spin Mode is exited and Service Mode is restored. 7 8")"8"4)@8")@5&$)."/6 JOEE

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60

ALIGNMENT AND ADJUSTMENTS
7
Service Mode
Service Mode:
1.
The washer must be on to go into the Service Mode.
2.
The motor speed will be displayed when started (It displays 0 when the motor does not spin).
3.
The present state of the machine will not be changed.
(i.e., the current cycle in progress will not be interrupted and only the display will change)
4.
To exit Service Mode, press Delay End and Pre Soak Key for 3 second again, or Power Key.If
no key is operated during Service Mode for 5 minutes, the machine will return to normal user
mode.
Quick Spin Test Mode
Deļ¬nition of Quick Spin Test Mode:
-
Quick Spin Test Mode is to do Spin Check. (High RPM)
How to Enter:
-
During Service Mode, press the Delay End and Self Clean Key for 3 seconds to enter Quick Spin
Test Mode.
-
Cannot enter once the washing cycle has started.
Quick Spin Test Mode:
As it enters into the Quick Spin Test Mode, it starts spinning and reaches its maximum RPM.
Once the Spin speed reaches the maximum RPM, the speed drops immediately.
To hold Quick Spin Test Mode (entering Hold Speed Mode), press the Start/Pause button. If the
Start/Pause button is pressed during Quick Spin Test Mode, it will stop accelerating and hold its
spinning speed for 10 minutes before going back to Quick Spin Test Mode.
Also, to cancel the hold and allow Quick Spin Test Mode to continue, press the Delay End and Self
Clean Key together for 3 seconds.
If you hold down the Delay End and Self Clean key for three (3) seconds when the washing
machine is not in Hold Speed Mode, Quick Spin Mode is exited and Service Mode is restored.
To avoid risk of electrical shock, personal injury or death; disconnect power to washer
before servicing, unless testing requires power.
WARNING
Delay End
+ Pre Soak
Delay End + Self Clean
While it is not in Hold Speed Mode
Delay End + Self Clean
3 sec
While a cycle is not running
Delay End + Self Clean
for 3 sec or after 10 minutes
WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd
7
2014-1-6
15:56:28