Samsung WF219ANB User Manual (user Manual) (ver.1.0) (English) - Page 10

necessary by hand or the wrench included with your washer.

Get Samsung WF219ANB PDF manuals and user guides View all Samsung WF219ANB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

installing your washer 2. Check the inlet hose to ensure a washer is inside each fill hose. Cold Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and install each fill hose to the water valve. Make sure the hose with the Hot printed line is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers. Hot Rubber washer For correct water use, connect both HOT and COLD water valves. If either or both are not connected, an "nF" (no fill) error can occur. Cold printed 3. Turn on the "HOT" and "COLD "water supply and check all connections at the water valve and the faucet for leaks. Hot printed 4. Plug the power cord into a 3-Prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded receptacle. 5. Slide your washer into position. 6. Level your washer by turning the leveling legs in or out as necessary by hand or the wrench included with your washer. When your washer is level, tighten the nuts using the wrench or (-) driver. Your Washer must be leveled on all four sides. A carpenter's level should be used on all four corners of your Washer. It's a good idea after the first dozen washes to recheck your washer's levelness. Avoid the damage to the legs, Do not move the Washer unless the Lockingnuts are fastened to the bottom of the Washer. 10_ installing your washer WF218ANB-02440B-04_EN.indd 10 2009-03-06 ¿ÀÈÄ 4:13:59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
10_
installing your washer
2.
Check the inlet hose to ensure a washer is inside each fill
hose.
Thread the inlet hoses to the HOT and COLD faucet
connections.
On the other end of the hose, check for one rubber washer
per hose and install each fill hose to the water valve. Make
sure the hose with the Hot printed line is attached to the
HOT faucet. Tighten by hand until snug, then two-thirds of a
turn with pliers.
For correct water use, connect both HOT and COLD water
valves. If either or both are not connected, an “nF” (no fill)
error can occur.
3.
Turn on the “HOT” and “COLD “water supply and check all
connections at the water valve and the
faucet for leaks
.
4.
Plug the power cord into a 3-Prong, well grounded 120 volt
60 Hz approved electrical outlet protected by a 15-amp fuse
or comparable circuit breaker.
Your washer is grounded through the third prong of the
power cord when plugged into a three-prong grounded
receptacle.
5.
Slide your washer into position.
6.
Level your washer by turning the leveling legs in or out as
necessary by hand or the wrench included with your washer.
When your washer is level, tighten the nuts using the wrench
or (-) driver.
Your Washer must be leveled on all four sides. A carpenter’s
level should be used on all four corners of your Washer. It’s
a good idea after the first dozen washes to recheck your
washer’s levelness.
Avoid the damage to the legs, Do not
move the Washer unless the Locking-
nuts are fastened to the bottom of the
Washer.
installing your washer
Cold
Hot
Cold printed
Hot printed
Rubber washer
WF218ANB-02440B-04_EN.indd
10
2009-03-06
¿ÀÈÄ 4:13:59