Samsung WF330ANW/XAA (English) - Page 15

Step 2, Step 3 - shipping bolts

Get Samsung WF330ANW/XAA PDF manuals and user guides View all Samsung WF330ANW/XAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

01 SETTING UP STEP 2 Removing the shipping bolts Before using your washer, you must remove the four shipping bolts from the back of the unit. 1. Loosen all the bolts with the supplied wrench. 2. Slide the bolt and spacer up and remove the bolt with the spacer through the hole in the rear wall of your washer. Repeat for each bolt. 3. Fill the holes with the supplied bolt hole covers. 4. Keep the shipping bolts and spacers for future use. STEP 3 Installing your washer 1. Place the drain hose in the drain facility. Be sure an airtight connection is NOT made between the drain hose and the standpipe. The standpipe must be at least 18in.(46 cm) high. Caution must always be exercised to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way - by elbows, couplings, or excessive lengths. For situations where the drain hose cannot be conveniently elevated to at 96" Max least 18in.(46 cm), the drain hose must 18" Min be supported. Laundry tub Hose Guide Stand pipe Hose retainer Tie strap 96" Max 18" Min 2. Before connect the inlet hoses to water faucets, check to ensure a washer is inside coupling. Coupling Rubber Washer WF350AN-02833A_EN.indd 15 setting up your new washing machine _15 2010-02-11 ¿ÀÀü 11:42:12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
setting up your new washing machine
_15
01 SETTING UP
STEP 2
Removing the shipping bolts
Before using your washer, you must remove the four
shipping bolts from the back of the unit.
1.
Loosen all the bolts with the supplied wrench.
2.
Slide the bolt and spacer up and remove the bolt with
the spacer through the hole in the rear wall of your
washer. Repeat for each bolt.
3.
Fill the holes with the supplied bolt hole covers.
4.
Keep the shipping bolts and spacers for future use.
STEP 3
Installing your washer
1.
Place the drain hose in the drain facility.
Be sure an airtight connection is NOT
made between the drain hose and the
standpipe.
The standpipe must be at least 18in.(46
cm) high.
Caution must always be exercised to
avoid collapsing or damaging the drain
hose. For best results, the drain hose
should not be restricted in any way – by
elbows, couplings, or excessive lengths.
For situations where the drain hose
cannot be conveniently elevated to at
least 18in.(46 cm), the drain hose must
be supported.
2.
Before connect the inlet hoses to water faucets, check to
ensure a washer is inside coupling.
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie
strap
Laundry tub
Stand pipe
Hose
Guide
Rubber
Washer
Coupling
WF350AN-02833A_EN.indd
15
2010-02-11
¿ÀÀü 11:42:12