Sanyo DP47460 Owners Manual - Page 5

Getting Started, Positioning The Hdtv

Page 5 highlights

POSITIONING THE HDTV • Always use a firm and flat surface when positioning your HDTV. • Do not position the unit in a confined area. • Allow adequate space for proper ventilation. • Do not position the HDTV where it is easily reachable by small children and may present risk of injury. STAND REMOVAL 1 Place HDTV face down on a padded or cushioned flat surface to protect the screen and finish 2 Remove the four (4) screws securing the foot stand. CAUTION: Hold the stand firmly as you remove the last screw. GETTING STARTED BATTERY INSTALLATION Install two (2) "AAA" batteries in the remote control. (Not included) To ensure safe operation, please observe the following precautions: • Replace both batteries at the same time. Do not use a new battery with a used battery. • There's a risk of explosion if a battery is replaced by an incorrect type. • Do not expose the Remote Control unit to moisture or heat. • Be sure to match the "+" and "-" signs on the batteries with marks inside the remote control. STAND ASSEMBLY ___________ 1 Place HDTV face down on a padded or cushioned flat surface to protect the screen and finish 2 Carefully insert the stand base to the bottom of the HDTV and secure the base by inserting 4 screws as indicated in the above diagram. NOTE: If your HDTV came packed with the Stand Base unassembled, these screws will be found in the literature package. WALL MOUNTING Wall mounting of the HDTV must be performed by a skilled person. Use the screws you would use to attach the stand base to secure the HDTV to a wall mounting kit (not included.) VESA standard interface: 400 x 400 Mounting screws measurements: M6 (6mm) Diameter, Length-12mm (maximum) Need help? ANTENNA CONNECTION FOR OFF-AIR SIGNALS OR CABLE Hook up your antenna or your cable service to the HDTV's ANT terminal with the use of a 75 OHM coaxial cable. NOTE: Keep your indoor antenna at least 3 ft. away from the television set and any other electronic equipment. ANTENNA CABLE ANALOG / DIGITAL ANTENNA IN The tuner in this HDTV can receive: • Digital and Analog off air signals from an antenna • Analog or ClearQAM cable channels from a direct Cable TV connection. www.sanyoctv.com 1-877-864-9604 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

5
Need help?
www.sanyoctv.com
1-877-864-9604
GETTING STARTED
Install two (2) “AAA” batteries in the remote
control. (Not included)
To ensure safe operation, please observe the
following precautions:
Replace both batteries at the same time. Do not use a
new battery with a used battery.
There’s a risk of explosion if a battery is replaced by
an incorrect type.
Do not expose the Remote Control unit to moisture
or heat.
Be sure to match the
“+”
and
signs on the
batteries with marks inside the remote control.
ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE
ANTENNA
CABLE
ANALOG / DIGITAL
ANTENNA IN
BATTERY INSTALLATION
Hook up your antenna or your cable service to
the HDTV’s
ANT
terminal with the use of a 75
OHM coaxial cable.
NOTE: Keep your indoor antenna at least 3 ft. away
from the television set and any other electronic
equipment.
The tuner in this HDTV can receive
:
Digital and Analog off air signals from an antenna
Analog or ClearQAM cable channels from a direct
Cable TV connection.
1
Place HDTV face down
on a padded or
cushioned flat surface to protect the screen
and finish
2
Remove the four (4) screws securing the foot
stand.
CAUTION:
Hold the stand firmly as you
remove the last screw.
STAND REMOVAL ____________
POSITIONING THE HDTV
Always use a firm and flat surface when
positioning your HDTV.
Do not position the unit in a confined area.
Allow adequate space for proper ventilation.
Do not position the HDTV where it is easily
reachable by small children and may present
risk of injury.
1
Place HDTV face down
on a padded or
cushioned flat surface to protect the screen
and finish
2
Carefully insert the stand base to the bottom
of the HDTV and secure the base by inserting
4 screws as indicated in the above diagram.
NOTE: If your HDTV came packed with the Stand Base
unassembled, these screws will be found in the
literature package.
STAND ASSEMBLY ___________
Wall mounting of the HDTV must be performed
by a skilled person.
Use the screws you would use to attach the stand
base to secure the HDTV to a wall mounting kit
(not included.)
VESA standard interface:
400 x 400
Mounting screws measurements:
M6 (6mm) Diameter, Length—12mm (maximum)
WALL MOUNTING ____________