Sanyo PLC-XC55 Owner's Manual - Page 50

Ceiling, Standby mode, Power management, Ready.When the lamp has been fully cooled - ceiling mount

Get Sanyo PLC-XC55 - 3100 Lumens PDF manuals and user guides View all Sanyo PLC-XC55 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Setting Ceiling When this function is "On", the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling mounting the projector. Rear When this function is "On", the picture is left/right reversed. This function is used to project the image to a rear projection screen. Ceiling Rear Standby mode This function is available when the projector is turned off and in Stand-by. It is recommended to use Eco under normal condition. Normal n o r m a l p o w e r c o n s u m p t i o n i n Stand-by condition. Eco lower power consumption than Normal mode in Stand-by condition. Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a certain period. When the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with "No signal" appears. The countdown starts to turn off the lamp. Select one of the operations: Ready When the lamp has been fully cooled down, the POWER indicator changes to green blinking. In this condition, the projection lamp is turned on if the input signal is reconnected or any button on the top control or remote control is pressed. Shut down . . . . When the lamp has been fully cooled down, the power is turned off. Off Power management function is off. Then set the countdown timer with the Point ◄►buttons. Note: Factory default is " Ready, 5 min". 50 Power management Time left before Lamp is off. Press the SELECT button at Power management and this box appears. Choose one of three settings with the Point ◄ ► buttons, and go to the timer with the Point ▲▼ buttons and set time with the Point ◄►buttons.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
50
Setting
Ceiling
When this function is "On", the picture is top/bottom and
left/right reversed.
This function is used to project the
image from a ceiling mounting the projector.
Rear
When this function is "On", the picture is left/right reversed.
This function is used to project the image to a rear
projection screen.
Ceiling
Rear
Standby mode
This function is available when the projector is turned off
and in Stand-by.
It is recommended to use Eco under
normal condition.
Normal. . . . . . . . . . normal power consumption in
Stand-by condition.
Eco. . . . . . . . . . . . . lower power consumption than
Normal mode in Stand-by condition.
Power management
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the projector is not used for a certain
period.
When the input signal is interrupted and no button is
pressed for more than 30 seconds, the timer display with
"No signal" appears.
The countdown starts to turn off the
lamp.
Select one of the operations:
Ready. . . . . . . . When the lamp has been fully cooled
down, the POWER indicator changes
to green blinking. In this condition, the
projection lamp is
turned on if the input
signal is reconnected or any button
on the top control or remote control is
pressed.
Shut down
. . . . When the lamp has been fully cooled
down, the power is turned off.
Off
. . . . . . . . . . Power management function is off.
Then set the countdown timer with the Point
◄►
buttons.
Time left before Lamp is off.
Press the SELECT button
at Power management
and this box appears.
Choose one of three
settings with the Point
◄
►
buttons, and go to the
timer with the Point
▲▼
buttons and set time with
the Point
◄►
buttons.
Power management
Note:
Factory default is " Ready, 5 min".