Sanyo PLC-XD2200 Owner's Manual - Page 53

Remote control, Lamp control

Get Sanyo PLC-XD2200 - XGA Able Multimedia Projector PDF manuals and user guides
UPC - 086483078644
View all Sanyo PLC-XD2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Lamp control This function allows you to change brightness of the screen. High Brighter than the Normal mode. Normal....... Normal brightness Eco Lower brightness reduces the lamp power consumption and extends the lamp life. ✔Note: • Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized. Lamp control Setting Remote control This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. When operating the projector in Code 2, both the projector and the remote control must be switched to Code 2. Remote control To change the code for the projector: Select either Code 1 or Code 2 in this Setting Menu. To change the code for the remote control: Press and hold both the MENU and IMAGE buttons together for 5 seconds or more. After changing the code, make sure the remote control operates properly. ✔Note: • When different codes are set on the projector and on the remote control, any operation cannot be made. In that case, switch the code on the remote control to fit the code on the projector. • If the batteries are removed from the remote control for a long period of time, the remote control code will be reset. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
5±
Setting
Remote control
This function allows you to change brightness of the
screen.
Lamp control
Lamp control
✔
Note:
• Lamp mode cannot be changed for a while after turning
on the projector. Lamp needs some time to stabilize
after the power is turned on. Stored lamp mode will be
active after the lamp is stabilized.
This projector provides two different remote control codes:
the factory-set initial code (
Code 1
) and the secondary code
(
Code 2
). This switching function prevents remote control
interference when operating several projectors or video
equipment at the same time.
When operating the projector in
Code 2
, both the projector
and the remote control must be switched to
Code 2
.
To change the code for the projector:
Select either
Code 1
or
Code 2
in this Setting Menu.
To change the code for the remote control:
Press and hold both the MENU and IMAGE buttons
together for 5 seconds or more. After changing the code,
make sure the remote control operates properly.
✔
Note:
• When different codes are set on the projector and on the remote control, any operation cannot be made. In that case,
switch the code on the remote control to fit the code on the projector.
• If the batteries are removed from the remote control for a long period of time, the remote control code will be reset.
High
...........
Brighter than the Normal mode.
Normal
.......
Normal brightness
Eco
............
Lower brightness reduces the lamp
power consumption and extends the
lamp life.
Remote control