Sanyo PLC-XU88 User Manual
Sanyo PLC-XU88 Manual
 |
View all Sanyo PLC-XU88 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC-XU88 manual content summary:
- Sanyo PLC-XU88 | User Manual - Page 1
Multimedia Projector MODEL PLC-XU88 Network Supported □ Wireless LAN IEEE802.11b/g □ Wired LAN 100-Base-TX/10-Base-T Memory Viewer □ SD Card Memory Viewer * Refer to the owner's manuals below for details about network and memory viewer function. ■ Network Set-up and Operation ■ Memory - Sanyo PLC-XU88 | User Manual - Page 2
- Sanyo PLC-XU88 | User Manual - Page 3
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. ◆ Compact Design This projector card memory is not supplied with the projector. For details, refer to the owner's manual of Memory viewer. ◆ Input Search Function - Sanyo PLC-XU88 | User Manual - Page 4
and Cleaning 57 WARNING TEMP. indicator 57 Cleaning the Filter 58 Resetting the Filter Counter 58 Attaching the Lens Cap 59 Cleaning the Projection Lens 59 Cleaning the Projector Cabinet 59 Lamp Replacement 60 Resetting the Lamp Counter 61 Appendix 62 Troubleshooting 62 Menu - Sanyo PLC-XU88 | User Manual - Page 5
operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the back of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC - Sanyo PLC-XU88 | User Manual - Page 6
local power company. Follow all warnings and instructions marked on the projector. For added protection to the projector during a lightning storm, or Refer all servicing to qualified service personnel. Unplug this projector from wall outlet and refer servicing to qualified service personnel under - Sanyo PLC-XU88 | User Manual - Page 7
in an unsuitable transport case. This may cause damage to the projector. For information about transporting the projector by courier or any other transport service, consult your dealer. -Do not put the projector in a case before the projector is cooled enough. Air Intake Vent Exhaust Vent (Hot air - Sanyo PLC-XU88 | User Manual - Page 8
tested and found to comply with the limits for a Class B digital user instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number : PLC-XU88 Trade Name : Sanyo Responsible party : SANYO red. WARNING: THIS APPARATUS MUST - Sanyo PLC-XU88 | User Manual - Page 9
Names and Functions Front Back ⑦ ⑥ Bottom ⑮⑯ ⑰ ⑱ ① Infrared Remote Receiver ② Focus Ring ③ Zoom Lever ④ Projection Lens ⑤ Lens Cap (See page 59 for attaching.) CAUTION Do not turn on a projector with lens cap attached. High temperature from light beam may damage lens cap and result - Sanyo PLC-XU88 | User Manual - Page 10
PAGE ▲▼buttons on the remote control during a presentation, connect the USB port of the computer to the USB terminal with a USB cable (not supplied) (pp.12, 18). ② SERVICE PORT This jack is used to service the projector. ③ COMPUTER IN 1/DVI-I Connect computer output (Digital/Analog DVI-I type) to - Sanyo PLC-XU88 | User Manual - Page 11
or return to the menu bar in Memory Viewer menu. Refer to the owner's manual of "Network Set-up and Operation" and owner's manual of Memory viewer. ④ POWER indicator -Lights red when the projector is in stand-by mode. -Lights green during operations. -Blinks green in the Power management mode (p.51 - Sanyo PLC-XU88 | User Manual - Page 12
③ SIGNAL EMISSION indicator Lights red while the laser beam is being emitted from the laser light window or a signal is being sent from the remote control to the projector. ④ Laser Light window A laser beam is emitted from here (p.13). ⑤ VIDEO button Select the VIDEO input source. (p.39) ⑥ COMPUTER - Sanyo PLC-XU88 | User Manual - Page 13
remote control code will be reset, as well. Spotlight Pointer PRESENTATION POINTER button LASER button After the Laser pointer has switched to the Pointer, use the LASER button as the Pointer function ON-OFF switch. Press the LASER button pointing toward the projector and see if it lights green - Sanyo PLC-XU88 | User Manual - Page 14
remote controls when several projectors or video equipment next to each other are operated at the same time. Change the remote control code for the projector first before changing that for the remote control. See "Remote the remote control code, slide the RESET/ ON/ALL-OFF switch to "RESET," and - Sanyo PLC-XU88 | User Manual - Page 15
an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Operating Range Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum operating range for the remote control is about 16.4'(5 m) and 60 degrees in front - Sanyo PLC-XU88 | User Manual - Page 16
Installation Positioning the Projector For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. Notes: • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to - Sanyo PLC-XU88 | User Manual - Page 17
system. If you are not sure of the type of power being supplied, consult your authorized dealer or service station. Connect the projector with all peripheral equipment before turning the projector on. CAUTION The AC outlet must be near this equipment and must be easily accessible. Notes: Unplug the - Sanyo PLC-XU88 | User Manual - Page 18
COMPUTER IN 2 / COMPONENT IN / MONITOR OUT. • USB cable connection is needed when operating the computer with the remote control or using the PAGE ▲▼ buttons on the remote control. 18 Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. - Sanyo PLC-XU88 | User Manual - Page 19
Cable • Audio Cable (Cables are not supplied with the projector. ) Composite Video and Audio Output S-Video Output (R) (L) (Video) S-Video cable Video and audio cable External Audio Equipment Audio Input S-VIDEO AUDIO IN VIDEO Audio cable (stereo) AUDIO OUT (stereo) Notes: • When the - Sanyo PLC-XU88 | User Manual - Page 20
• Audio Cables • Scart-VGA Cable • Component Cable • Component-VGA Cable (Cabels are not supplied with this projector.) Installation RGB Scart 21pin Output Component Video Output (Y, Pb/Cb, Pr/Cr) Audio Output Component cable Scart-VGA cable ComponentVGA cable Audio cable (stereo - Sanyo PLC-XU88 | User Manual - Page 21
.) before turning on the projector. 2 Connect the projector's AC power cord into an AC outlet. The POWER indicator lights red. Open the lens cap (see pages 9,59). 3 Press the POWER ON/SYAND-BY button on the top control or on the remote control. The POWER indicator lights green and the cooling fans - Sanyo PLC-XU88 | User Manual - Page 22
according to the temperature inside the projector. • Do not put the projector in a case before the projector is cooled enough. • If the WARNING TEMP. indicator blinks or lights red, see "WARNING TEMP. indicator" on page 57. • While the POWER indicator is blinking, the lamp is being cooled down and - Sanyo PLC-XU88 | User Manual - Page 23
Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. 1 Press the MENU button on the top control or the remote control to display the On-Screen Menu. 2 Use - Sanyo PLC-XU88 | User Manual - Page 24
Digital zoom +/-] Image 1- 4 (p.35). (pp.37-38). Used to set the projector's operating configurations (pp.46-56). Wireless Menu See owner's manual system of selected video source (p.41). Image Adjust Menu Used to adjust picture image [Contrast/Brightness/Color/Tint/ Color temp./White balance - Sanyo PLC-XU88 | User Manual - Page 25
distortion according to the projector's tilt and adjust the Auto Keystone cannot work when Ceiling feature is set to "On" in the , adjust manually by pressing the KEYSTONE button on the remote control or indicate that there is no correction. • A red arrow indicates the direction of correction. • An - Sanyo PLC-XU88 | User Manual - Page 26
buttons. The Mute function is also effective for the AUDIO OUT jack. Remote Control VOLUME+/buttons VOL- button VOL+ button Menu Operation 1 Press the ◄► buttons to move the red frame pointer to the Sound Menu icon. 2 Use the Point ▲▼ buttons to move the red frame pointer to the desired item - Sanyo PLC-XU88 | User Manual - Page 27
operation quickly without calling up the On-Screen Menu. COMPUTER/VIDEO/NETWORK button Press the COMPUTER, VIDEO, or NETWORK button on the remote control to select the input source. See pages 2930, 39-40 for details. Refer to the owner's manual "Network Set-up and Operation" for details about the - Sanyo PLC-XU88 | User Manual - Page 28
NO SHOW button Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as "User" in the Logo selection (see page 48), the screen changes each time - Sanyo PLC-XU88 | User Manual - Page 29
2 Video Wired Remote Control Wireless COMPUTER button Computer 1 (Analog) Computer 1 (Digital) Menu Operation 1 Press the MENU button to display the On-Screen Menu. Use the Point ◄► buttons to move the red frame pointer to the Input Menu icon. 2 Use the Point ▲▼ buttons to move the red arrow - Sanyo PLC-XU88 | User Manual - Page 30
of HDCP is decided and controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP. • Wired and Wireless are for the Network function. See owner's manual "Network Set-up and Operation" . • When the - Sanyo PLC-XU88 | User Manual - Page 31
projector. (See "Troubleshooting" on page 63.) The preset system is manually projector. *Mode 1 and SVGA 1 are examples. Selecting Computer System Manually PC system can also be selected manually. 1 Press the MENU button to display the On-Screen Menu. Use the Point ◄► buttons to move the red - Sanyo PLC-XU88 | User Manual - Page 32
button on the remote control. Remote Control AUTO PC red frame pointer to Auto PC Adj. and then press the SELECT button twice. To store adjustment parameters The adjusted parameters from the Auto PC Adjustment can be stored in the projector with this operation, manual adjustments are required ( - Sanyo PLC-XU88 | User Manual - Page 33
those signal formats. The projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen Menu. Use the Point ◄► buttons to move the red frame pointer to the PC - Sanyo PLC-XU88 | User Manual - Page 34
projector. Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select [Yes]. All adjustments will return to their previous figures. Move the red when Computer 1(Digital) is selected in the Input Menu (p.30). 34 Close this dialog box. - Sanyo PLC-XU88 | User Manual - Page 35
preset on the projector. Real Picture mode with improved halftone for graphics. Blackboard(Green) For the image projected on a blackboard. See above for further description. Image 1~4 For viewing with the user preset image mode in the Image Adjust Menu (see pages 36-37). Remote Control IMAGE button - Sanyo PLC-XU88 | User Manual - Page 36
temp. Use the Point ◄► buttons to select the desired Color temp. level (High, Mid, Low, or XLow). White balance (Red) Press the Point ◄ button to lighten red tone; press the Point ► button to deepen red (from 0 to 15). Reset To reset the adjusted data, select Reset and press the SELECT button. - Sanyo PLC-XU88 | User Manual - Page 37
If your computer's screen resolution is higher than it, reset the resolution to the lower before connecting to the projector. • The image data in other than 1024 x 768 is modified to fit the screen size in initial mode. • True, Full, and Digital zoom +/- cannot be selected when 480i, 575i, 480p, or - Sanyo PLC-XU88 | User Manual - Page 38
also expanded by pressing the D.ZOOM ▲ button on the remote control. Digital zoom - Select Digital zoom -. The On-Screen Menu disappears and "D. zoom -" with the D.ZOOM ▲▼ buttons. 38 Press the SELECT button at Common or Reset, to display a confirmation box. Notes: • When no signal is detected, - Sanyo PLC-XU88 | User Manual - Page 39
the following order: 1. S-video 2. Video Video When video input signal is connected to the VIDEO jack, select Video. S-video When video input signal is connected to the SVIDEO jack, select S-video. Notes: • Wired and Wireless are for the Network function. See the owner's manual "Network Set-up - Sanyo PLC-XU88 | User Manual - Page 40
(red arrow) to Computer 2 and press the SELECT button. RGB (Scart) When the input source is coming from video equipment connected to the COMPUTER IN 2/COMPONENT IN terminal with a ScartVGA Cable, select RGB (Scart). Note: • Wired and Wireless are for the Network function. See owner's manual - Sanyo PLC-XU88 | User Manual - Page 41
system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL - Sanyo PLC-XU88 | User Manual - Page 42
-4 For viewing with the user preset image mode in the Image Adjust Menu (see pages 43-44). 42 Video Input Remote Control IMAGE button IMAGE button Dynamic Standard Cinema Blackboard (Green) Image 1 Image 2 Image 3 Image 4 Image Select Menu Image Select Menu icon Move the red frame pointer to the - Sanyo PLC-XU88 | User Manual - Page 43
the Point ► button to deepen blue tone (from 0 to 63). Notes: • When the White balance Red, Green, or Blue is adjusted, the Color temp. level will change to "Adj.". • Tint cannot be selected when the video system is PAL, SECAM, PAL-M, or PAL-N (p.41). Image Adjust Menu Image Adjust Menu icon Move - Sanyo PLC-XU88 | User Manual - Page 44
function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the (p.41). • Reset and Store icons will be displayed when any adjustment is made. 44 Video Input Store icon Image Mode Menu Move the red frame pointer to - Sanyo PLC-XU88 | User Manual - Page 45
Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size. 1 Press the MENU button to display the On-Screen Menu. Use the Point ◄► buttons to move the red frame pointer to the Screen Menu icon. Screen Menu 2 Use the - Sanyo PLC-XU88 | User Manual - Page 46
projector's tilt. Manual... Works only when pressing the AUTO SET/ CANCEL button on the remote distortion. • The Auto Keystone cannot work when Ceiling feature is set "On" in the Setting menu (p.50 operation, manual adjustments are required (pp.33-34). 46 Setting Menu (Language) Set the red frame - Sanyo PLC-XU88 | User Manual - Page 47
the keystone correction even when the AC power cord is unplugged. Reset........ Release the keystone correction when the AC power cord is unplugged. when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. - Sanyo PLC-XU88 | User Manual - Page 48
XGA (1024 x 768). A signal from video equipment can be captured except for 720p, 1035i, and 1080i. • When capturing the image that has been adjusted by the Keystone function, the adjusted data is automatically reset and the projector while capturing a image, "User" cannot be selected, you - Sanyo PLC-XU88 | User Manual - Page 49
. After entering the four-digit number, move the pointer to "Set." Press the SELECT button so that you can start to operate the projector. If you entered an incorrect Logo PIN code, "Logo PIN code" and the number will turn red for a moment. Enter the correct Logo PIN code all over again. Change - Sanyo PLC-XU88 | User Manual - Page 50
button or VIDEO button on the remote control. On2........ Input search works under the following situation. - When turning on the projector by pressing Input search is set to "On1" or "On2," the status of Input and Lamp are displayed every time the signal is switched. • Only the last selected input - Sanyo PLC-XU88 | User Manual - Page 51
to the owner's manual "Network Set-up and Operation". Note: • When selecting Normal, the cooling fans may be running depending on the temperature inside the projector even if the projector is turned off. Power management For reducing power consumption as well as maintaining the lamp life, the - Sanyo PLC-XU88 | User Manual - Page 52
and Eco mode). Eco Lower brightness reduces the lamp power consumption and extends the lamp life. Pointer Pointer You can emphasize a part the IMAGE button the number of times corresponding to the remote control code for the projector. See "Remote Control Code" on page 14. Use the Point ▲▼ - Sanyo PLC-XU88 | User Manual - Page 53
the remote control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center , the projector can be operated without a PIN code. Whenever you change the PIN code lock setting or the PIN code (the four-digit number), - Sanyo PLC-XU88 | User Manual - Page 54
this step to complete entering a four-digit number. After entering the four-digit number, move the pointer to "Set." Press the SELECT button so that you can start to operate the projector. If you entered an incorrect PIN code, "PIN code" and the number will turn red for a moment. Enter the correct - Sanyo PLC-XU88 | User Manual - Page 55
properly and that causes malfunctions of the projector and decreases the lamp life. Warning log This function records anomalous operations while the projector is in operation and use it when diagnosing faults. Up to 10 warning logs are displayed with the latest warning message at the top of the list - Sanyo PLC-XU88 | User Manual - Page 56
for the filter cleaning. When the projector reached a specified time between cleanings, a Filter warning icon appears on the screen, notifying the cleaning is necessary. After cleaning the filter, be sure to select RESET and set the timer. The Filter warning icon will not turn off until the - Sanyo PLC-XU88 | User Manual - Page 57
on and the Warning Temp. indicator still lights red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. Top Control WARNING TEMP. emit a red light 57 - Sanyo PLC-XU88 | User Manual - Page 58
heat buildup and adversely affect the life of the projector. If a "Filter warning" icon appears on the screen, clean the air LCD panels, or optical elements inside the projector degrading the quality of a projected image. When the symptoms above are noticed, contact your authorized dealer or service - Sanyo PLC-XU88 | User Manual - Page 59
an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the cabinet. When the projector is not in use, put the projector in an appropriate carrying case to protect it from dust and scratches. Lens Cap Hole String for the lens cap Secure - Sanyo PLC-XU88 | User Manual - Page 60
Screw Handle Screw ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-XU88 : POA-LMP115 (Service Parts No. 610 334 - Sanyo PLC-XU88 | User Manual - Page 61
a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion. ● A Lamp may explode as a result of vibration - Sanyo PLC-XU88 | User Manual - Page 62
blinking to turn on the projector again. The projector can be turned on after the POWER indicator turns red. See page 21. - Check the WARNING TEMP.indicator. If the WARNING TEMP. indicator lights red, projector cannot be turned on. See page 57. - Check the projection lamp. See page 60. - Unlock the - Sanyo PLC-XU88 | User Manual - Page 63
projector. See your computer's instruction manual for the setting. - It takes about 30 seconds to display an image after turning on the projector. See page 21. - Check the Input singal, color system, video not available in grayout when the digital signal is input. The setting - Sanyo PLC-XU88 | User Manual - Page 64
RESET/ON/ALL-OFF switch on the remote control is set to "ON". See page 14. Indicator blinks or lights. - Chek the status of the projector with referring to "Indicators and projector dealer where you purchased the projector or the service code lock, Security key lock center. or Security PIN - Sanyo PLC-XU88 | User Manual - Page 65
WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem - Sanyo PLC-XU88 | User Manual - Page 66
digital) RGB (AV HDCP) Quit RGB Component RGB (Scart) Quit Auto Video S-video Quit 0-63 On/Off Go to System (1) N/A N/A Go to System (1) Go to System (2) N/A Go to System (3) Go to System (3) Go to System (3) See owner's manual Brightness Color temp. Red Green Blue Sharpness Gamma Reset Store Quit - Sanyo PLC-XU88 | User Manual - Page 67
/Auto/Eco Spotlight/Pointer Quit Code 1-Code 8 Key lock Off Projector Remote control Quit PIN code lock Off/On1/On2 PIN code change Quit Fan Fan control Warning log Lamp counter Filter counter Factory default Quit Quit L1/L2 Normal/Max Hour(s) Reset Yes/No Quit Hour(s) Off/100H/200H/300H - Sanyo PLC-XU88 | User Manual - Page 68
Condition Check the indicators for projector condition. Indicators WARNING LAMP POWER TEMP. REPLACE red/green red yellow Projector Condition The projector is off. (The AC power cord is unplugged.) Appendix The projector is in stand-by mode. Press the POWER ON/STAND- BY button to - Sanyo PLC-XU88 | User Manual - Page 69
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below and less than 140 MHz of Dot Clock for analog signal and 110 MHz of Dot Clock for digital signal. When selecting these modes, PC adjustment can be - Sanyo PLC-XU88 | User Manual - Page 70
Appendix When the input signal is digital from DVI terminal, refer to the chart below. ON-SCREEN DISPLAY D-VGA D-480p D-575p D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 displayed properly depending on computers. • The specifications are subject to change without notice. 70 - Sanyo PLC-XU88 | User Manual - Page 71
Appendix Technical Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 335 mm x 79.7 mm x 238.4mm (Not including adjustable feet) Net Weight 3.4 kg Feet Adjustment 0˚ to 10˚ Panel Resolution LCD Panel System 0.63" TFT Active - Sanyo PLC-XU88 | User Manual - Page 72
Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable Lens Cap with String PIN Code Label Lamp Replacement Label Network Application (CD-ROM) ● The specifications are subject to change without notice. ● LCD panels - Sanyo PLC-XU88 | User Manual - Page 73
1. For PJ Link password, see page 49 on the owner's manual "Network Set-up and Operation." Projector Input Computer1 (Analog) Computer1 (Digital) RGB (PC digital) RGB (AV HDCP) RGB Computer2 Component RGB (Scart) Auto Video Video S-video Wired Wireless Memory viewer PJLink Input RGB - Sanyo PLC-XU88 | User Manual - Page 74
. sync. Input/Output (Composite H/V sync.) 14 Vert. sync. 15 DDC Clock/----- DVI-I TERMINAL (DIGITAL/ANALOG) C1 C2 12345678 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C3 C4 C5 C1 Analog Red Input C2 Analog Green Input C3 Analog Blue Input C4 Analog Horiz. sync - Sanyo PLC-XU88 | User Manual - Page 75
Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set - Sanyo PLC-XU88 | User Manual - Page 76
Dimensions 88.7(3.49) 246.3(9.70) 106.3(4.19) 136.3(5.37) 132.1(5.20) Appendix Unit: inch(mm) Screw Holes for Ceiling Mount Screw: M4 Depth: 0.472(12.0) 228(9.0) 53.5(2.11) 84.7(3.33) 4.5(0.18) 55(2.17) 105.5(4.15) 10°MAX 90(3.54) 70(2.76) 3.7(0.15) 5(0.2) 45(1.77) 40(1.57) 47.2(1.86) - Sanyo PLC-XU88 | User Manual - Page 77
KD3AC SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
 |
 |
Owner’s Manual
Network Supported
□
Wireless LAN
IEEE802.11b/g
□
Wired LAN
100-Base-TX/10-Base-T
Memory Viewer
□
SD Card Memory Viewer
*
Refer to the owner’s manuals below for details
about network and memory viewer function.
■
Network Set-up and Operation
■
Memory viewer
Multimedia Projector
MODEL
PLC-XU88