Sanyo PLC-XU88 User Manual - Page 63

after turning off power°, The setting does not remain

Get Sanyo PLC-XU88 PDF manuals and user guides View all Sanyo PLC-XU88 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Appendix No image - Check the connection between your computer or video equipment and the projector. See pages 18-20. - See if the input signal is correctly output from your computer. Some laptop computers may need to change the setting for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 30 seconds to display an image after turning on the projector. See page 21. - Check the Input singal, color system, video system or computer system mode. - Make sure the temperature is not out of the specified Operating Temperature (41˚F-95˚F [5˚C-35˚C]). - When "No Show" is operating, the image cannot be displayed. Press the NO SHOW button or any other button on the remote control. No sound - Check the audio cable connection from audio input source. - Adjust the audio source. - Press the Volume + button. See page 26. - Press the Mute button. See page 26. - When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available - Is the image projected? You will hear the sound only when the image is projected. The color is strange. - Check the Input signal, color system,video system or computer system mode. - Make sure the "Blackboard" is not selected on Image select menu.(see page 35,42) Some displays are not seen during the operation. - Check the Display function. See page 47. Auto PC adjustment function - Check the Input signal. Auto PC function can not work when does not work. 480p,575p.720p,480i,575i,1035i or 1080i is selected or when the digital signal is input into DVI terminal.(see Page 32) - The icon is not available in grayout when the digital signal is input. The setting does not remain - Make sure you selected "Store" after adjusting setting. Some settings after turning off power. can not be stored if not registered with "Store".(see page 37,44) Power management does work. - Power management function can not work while "Freeze" or "No Show" function is running.(see page 51) Capture function does not work. - Check the connection and the input signal to see if there is signal. Auto setup does not work properly. - Make sure "Off" is not selected at the Auto setup function.(see page 25,46) - Make sure "On" is not selected at the Ceiling funtion.(see page 50) Auto keystone function does not work even when the projector is tipped. - Make sure the Auto keystone function is not set to "Manual". Press the AUTO SET UP button on the top control.(see page 25,46) 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
6²
Appendix
No image
– Check the connection between your computer or video equipment
and the projector. See pages 18-20.
– See if the input signal is correctly output from your computer. Some
laptop computers may need to change the setting for monitor output
when connecting to a projector. See your computer’s instruction
manual for the setting.
– It takes about 30 seconds to display an image after turning on the
projector. See page 21.
–
Check the Input singal, color system, video system or computer
system mode.
– Make sure the temperature is not out of the specified Operating
Temperature (
41˚F–95˚F [5˚C–35˚C])
.
– When "No Show" is operating, the image cannot be displayed. Press
the NO SHOW button or any other button on the remote control.
No sound
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. See page 26.
– Press the Mute button. See page 26.
– When the AUDIO OUT is plugged-in, the projector's built-in speaker
is not available
– Is the image projected? You will hear the sound only when the image
is projected.
The color is strange°
– Check the Input signal, color system,video system or computer
system mode.
– Make sure the "Blackboard" is not selected on Image select
menu.(see page 35,42)
Some displays are not seen
– Check the Display function. See page 47.
during
the operation°
Auto PC adjustment function
– Check the Input signal. Auto PC function can not work when
does not work°
480p,575p.720p,480i,575i,1035i or 1080i is selected or when the
digital signal is input into DVI terminal.(see Page 32)
– The icon is not available in grayout when the digital signal is input.
The setting does not remain
– Make sure you selected "Store" after adjusting setting. Some settings
after turning off power°
can not be stored if not registered with "Store".(see page 37,44)
Power management does
– Power management function can not work while "Freeze" or "No
work°
Show" function is running.(see page 51)
Capture function does not work°
– Check the connection and the input signal to see if there is signal.
Auto setup does not work properly°
– Make sure "Off" is not selected at the Auto setup function.(see page
25,46)
– Make sure "On" is not selected at the Ceiling funtion.(see page 50)
Auto keystone function does not
– Make sure the Auto keystone function is not set to "Manual". Press
work even when the projector is
the AUTO SET UP button on the top control.(see page 25,46)
tipped°