Sanyo XU83 Instruction Manual, PLC-XU83

Sanyo XU83 - PLC XGA LCD Projector Manual

Get Sanyo XU83 - PLC XGA LCD Projector PDF manuals and user guides View all Sanyo XU83 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo XU83 manual content summary:

  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 1
    Multimedia Projector MODEL PLC-XU86 PLC-XU83 Network Supported ❏ Wireless LAN IEEE802.11b/g ❏ Wired LAN 100-Base-TX/10-Base-T Memory Viewer ❏ USB Memory Viewer (optionally available) Compatible with a dedicated USB memory ✽Refer to the owner's manuals below for details about network and memory
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 2
    2
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 3
    with Wired and Wireless LAN network function. You can project an image on a computer via the network. You can also operate and manage the projector via the network. For details, refer to the owner's manual (Additional Vol.) "Network Set-up and Operation". Operation menu is available in 16 languages
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 4
    10 Top Control 11 Remote Control 12 Laser Pointer Function 13 Pointer Function 13 Wireless Mouse Operation 14 Remote Control Code 14 Remote Control Battery Installation 15 Operating Range 15 Adjustable Feet 15 Installation 16 Positioning the Projector 16 Connecting the
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 5
    operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the end of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 6
    has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 7
    speed is changed according to the temperature inside the projector. Exhaust Vent Installing the Projector in Proper Position Install the projector properly. Improper Installation may reduce the lamp life and cause a fire hazard. 20˚ Do not tilt the projector more than 20 degrees from side to side
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 8
    unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers Trade Name Responsible party Address Telephone No. : PLC-XU86, PLC-XU83 : Sanyo : SANYO FISHER COMPANY : 21605 Plummer Street
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 9
    attaching.) u Infrared Remote Receiver i Top Controls and Indicators o Speaker !0 Air Intake Vent !1 Power Cord Connector !2 Terminals and Connectors !3 Lamp Cover !4 Air are for the Network function. Refer to the Additional Vol. and owner's manual of Memory viewer (optionally available). !7 !6 9
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 10
    to operate the computer with the remote control and use the PAGE ed buttons on the remote control during a presentation, connect the USB port of the computer to the USB terminal with a USB cable. (p12, 18) w SERVICE PORT This jack is used to service the projector. e COMPUTER IN 1 / DVI-I Connect
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 11
    detects abnormal condition. This also blinks red when the internal temperature of the projector exceeds the operating range. (p55, 64) u LAMP REPLACE indicator Turn yellow when the life of the projection lamp draws to an end. (p58, 64) i AUTO SETUP button Correct vertical keystone distortion
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 12
    of the projector or a pointer for wireless mouse operation. (p13.14) @3 AUTO SET button Correct vertical keystone distortion and adjust PC display parameters. (p25, 46) @4 NETWORK button Select network input or Memory viewer input. See owner's manual (Additional Vol.) and owner's manual of Memory
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 13
    so that the Pointer function will be available. (The Laser pointer has switched to the Pointer.) 2 Press the LASER button on the remote control toward the projector. Spotlight or Pointer is displayed on the screen with the LASER button lighting green. Then move the Spotlight or Pointer with the
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 14
    Part Names and Functions Wireless Mouse Operation The remote control can be used as a wireless mouse for your computer. Before operating the wireless mouse, connect your computer and the projector with the supplied USB cable. (See page 18 for connection.) When the Pointer function is used, the
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 15
    to the instructions. Operating Range Point the remote control toward the projector (Infrared Remote Receiver) whenever pressing any button. Maximum operating range for the remote control is about 16.4' (5m) and 60° in front of the projector. 16.4' (5 m) 60° Remote control Adjustable Feet
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 16
    Positioning the Projector For projector positioning, see the figures below. The projector should be 3048 x 2286 19.4' (5.9m) 12.5' (3.8m) 200" 4064 x 3048 25.9' (7.9m) 16.4' (5m) 300" 6096 x 4572 38.7' (11.8m) 24.9' (7.6m) PLC-XU83 A : B = 10 : 1 45.3' (13.8m) 19.4' (5.9m) 14.4' (4.4m
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 17
    plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power being supplied. Connect the projector with all peripheral equipment before turning the projector on. (See page 18-20 for connection.) CAUTION For safety, unplug the
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 18
    or Monitor output. (See Page 50.) Audio cable ✽ (stereo) RESET USB SERVICE PORT COMPUTER IN 1 DVI-I COMPUTER/ COMPONENT AUDIO IN (VARIABLE) COMPUTER IN the remote control or using the PAGE ed buttons on the remote control. When connecting the cable, the power cords of both the projector and
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 19
    Cable ✽ • Audio Cable ✽ (✽ = Not supplied with this projector.) Installation Installation S-video Output Composite Video and Audio Output (R) (L) audio cable✽ S-VIDEO (R) (L) (Video) AUDIO IN VIDEO RESET USB SERVICE PORT COMPUTER IN 1 DVI-I (VARIABLE) COMPUTER IN 2 / COMPONENT IN
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 20
    output. (See Page 50.) Audio cable ✽ (stereo) RESET USB SERVICE PORT COMPUTER IN 1 DVI-I COMPUTER/ COMPONENT AUDIO IN (VARIABLE) COMPUTER ) ✔Note: • When connecting AUDIO OUT to external audio equipment, the projector's built-in speaker is disconnected. • See p67 for ordering optional parts
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 21
    , consult your dealer or service center. 16 The preparation display will disappear after 30 seconds. Selected Input Source and Lamp Mode Lamp mode (See page 51 for Lamp mode.) PIN Code Input Dialog Box Pointer After the OK icon disappears, you can operate the projector. ✔Note: •When the Logo
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 22
    control or on the remote control, and a message "Power off?" will appear on the screen. 2 Press the POWER ON-OFF button again to turn off the projector •Do not operate the projector continuously without rest. Continuous use may result in shortening the lamp life. Turn off the projector and give it a
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 23
    Menu The projector can be buttons to select an item to adjust. Top Control ON - OFF POWER MENU WARNING INPUT LAMP REPLA AUTO SET UP SELECT - VOLUME + not active until the SELECT button is pressed. SELECT button Remote Control POINT buttons SELECT button MENU button On-Screen Menu Menu
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 24
    63. For computer source Guide Window PC System Menu Show adjust size Used to set the of image. [Normal / projector's operating True / Wide / Full configurations. screen / Digital Used to adjust computer Used to adjust See owner's manual parameters to match image. the volume or (Additional Vol
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 25
    control or the AUTO SET button on the remote control, correct the image manually as follows: Press the KEYSTONE button on the remote control Top Control ON - OFF POWER MENU WARNING INPUT LAMP REPLACE AUTO SET UP SELECT - VOLUME + VOLUME AUTO SET UP button POINT ed buttons Remote Control
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 26
    the sound will be cut off. To restore the sound to its previous level, press the Point 7 8 buttons again. Top Control SELECT - VOLUME + VOLUME VOLUME+/buttons Remote Control VOL- button VOL+ button MUTE button Approximate level of the volume. Press the MUTE button to set the Mute function On
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 27
    p29, 30, 39, 40. Refer to the owner's manual (Additional Vol.) for details about Network input. AUTO PC button FREEZE button COMPUTER/VIDEO /NETWORK button KEYSTONE button (See p25) AUTO SET button (See p25) Press the FREEZE button on the remote control to freeze the picture on the screen. To
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 28
    Basic Operation NO SHOW button Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as "User" in the Logo selection (p48), the screen changes each time you
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 29
    pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input RGB signal. •Wired, Wireless, Memory Viewer are for the Network function. See owner's manual (Additional Vol.) and owner's manual of Memory viewer (optionally
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 30
    top control or press the COMPUTER button on the remote control. controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP. •Wired, Wireless, Memory Viewer are for the Network function. See owner's manual
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 31
    . ----- There is no signal input from computer. Check the connection between your computer and the projector. (See " Troubleshooting" p60) Mode 1 The preset system is manually adjusted in the PC Adjust Menu. The adjusted data can be stored in Mode 1~5. (p33, 34) SVGA 1 PC Systems provided
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 32
    pressing the AUTO PC button on the remote control. Remote Control AUTO PC button Menu Operation Auto PC Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can is not provided properly with this operation, manual adjustments are required. (p33, 34) •
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 33
    PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 34
    . Press the Point 7 8 buttons to decrease/increase the value. Display area V Adjust the vertical area displayed by this projector. Press the Point 7 8 buttons to decrease/increase the value. Reset To reset the adjusted data, select Reset and press the SELECT button. The confirmation box
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 35
    on this projector. Real Picture level with improved halftone for graphics. Blackboard(Green) Picture level suitable for the image projected on a blackboard. See above for further description. Image 1~4 User preset image in the Image Adjust Menu (p37). Computer Input Remote Control IMAGE button
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 36
    Computer Input Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Image Adjust Menu icon. 2 Press the Point ed buttons to move the red framed pointer to the item that you want to adjust, and then press the
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 37
    . This function can be used for providing a squeezed video signal at 16 : 9. ✔Note: •This Screen Menu cannot be operated when 720p(HDTV), 1035i (HDTV), or 1080i (HDTV) is selected in the PC System Menu (p31). •This projector cannot display any resolution higher than 1600 X 1200. If your computer
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 38
    can work only when the image is larger than the screen size. A projected image can be also expanded by pressing the D.ZOOM ▲ button on the remote control. Digital zoom - When Digital zoom - is selected, the On-Screen Menu will disappear and the message "D. zoom -" will be displayed. Press the SELECT
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 39
    Monitor out is selected in the Terminal function (p50), Computer 2 is not displayed. •Wired, Wireless, Memory Viewer are for the Network function. See owner's manual (Additional Vol.) and owner's manual of Memory viewer (optionally available). VIDEO Move the pointer to Video and press the SELECT
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 40
    RGB(Scart) and press the SELECT button. ✔Note: •When Monitor out is selected in the Terminal function (p50), Computer 2 is not displayed. •Wired, Wireless, Memory Viewer are for the Network function. See owner's manual (Additional Vol.) and owner's manual of Memory viewer (optionally available). 40
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 41
    video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If the projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 42
    preset on this projector. Cinema Picture level adjusted for the picture with fine tone. Blackboard(Green) Picture level suitable for the image projected on a Blackboard. See above for further description. Image1~4 User preset image in the Image Adjust Menu (p43, 44). 42 Remote Control IMAGE button
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 43
    Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Image Adjust Menu icon. 2 Press the Point ed buttons to move the red framed pointer to the item that you want to adjust and then press the SELECT button.
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 44
    "L1" for an active picture. L2............Select "L2" for a still picture. Film .........Select "Film" for watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT button. The
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 45
    Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables you to and press the SELECT button. Wide Provide the image at a wide screen ratio of 16 : 9. ✔Note: Screen Menu cannot be operated when 720p, 1035i, or 1080i is selected in the AV System Menu
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 46
    Keystone Auto . . . . . always works and corrects keystone distortion according to the projector's tilt. Manual . . .works only when pressing the AUTO SET button on the remote control or the AUTO SETUP button on the top control. Off . . . . . .disables Auto Keystone. ✔Note: • Auto PC Adj. and Auto
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 47
    is this mode. Countdown off ......Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off Do not show On-Screen Displays. except; ● On-Screen Menu ● "Power
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 48
    or interval of presentations. After capturing the projected image, go to the Logo select function and set it to "User". Then the captured image will be displayed when turning on the projector next time or pressing the NO SHOW button. (p28) To capture the image, select [Yes]. To cancel the Capture
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 49
    Logo PIN code setting. For details on PIN code setting, refer to relevant instructions of the PIN code lock function on page 52, 53. CAUTION: WHEN YOU KEEP IT SECURELY. SHOULD THE LOGO PIN CODE BE LOST OR FORGOTTEN, THE PROJECTOR CAN NO LONGER BE OPERATED. Logo PIN code lock Dialog Box Pointer Quit
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 50
    when you do not use the projector via the network. The projector's network function will stop when turning off the projector. Refer to the owner's manual (Additional Vol.). Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 51
    Spotlight or a pointer of three different patterns (Arrow, Finger, and Dot) of Pointer. (See page 13 for operation.) Remote control This projector provides eight different remote control codes (Code 1-Code 8); the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). This
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 52
    allows you to use Key lock and PIN code lock function to set the security for the projector operation. Key lock This function locks operation of the top control or the remote control. It is useful to prevent operation by an unauthorized person. ···· not locked. ···· lock the operation of the
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 53
    NEW PIN CODE IN COLUMN OF THE PIN CODE NO. MEMO ON PAGE 70, AND KEEP IT SECURELY. IF YOU FORGET YOUR PIN CODE, THE PROJECTOR CAN NO LONGER BE STARTED. Enter a PIN code Quit Pointer The input numbers change to "✳" for security. When the pointer automatically moves to "Set", press
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 54
    the projector down. Lamp counter This function is used to reset the lamp replacement counter. When replacing the projection lamp, reset the lamp replacement returns all setting values except for the user logo, PIN code lock, Logo PIN code lock and the lamp counter to the factory default settings.
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 55
    cord and contact the service station for check and repair. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER THE ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. Top Control WARNING emit a red light ON - OFF POWER MENU WARNING INPUT LAMP REPLACE AUTO SET UP
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 56
    the life of the projector. Clean the air filters following the steps below. 1 Turn off the projector, and LCD panels, or optical elements inside the projector. This condition may degrade the quality of a projected image. When the symptoms above are noticed, contact your authorized dealer or service
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 57
    dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface. 3 When the projector is not in use, put the projector in an appropriate carrying case to protect it from dust and scratches. Maintenance and Cleaning 57
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 58
    Handle Screw Screw Lamp ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-XU86/ PLC-XU83 : POA-LMP90 (Service Parts No. 610
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 59
    a new one IMMEDIATELY after the projector has cooled down. ( Follow carefully the instructions in the Lamp Replacement section of this manual. ) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion. ● A Lamp may explode as a result of vibration
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 60
    Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. -Make sure you have properly connected the projector for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 30 seconds
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 61
    the AC plug. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Give the model number and explain about the
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 62
    1 (Analog) Computer 1 (Digital) Computer 2 Video Sound Wired Wireless ✽ Memory Viewer ✽ Sound Volume Mute Quit Computer Input System (1) (3) Go to System (3) See owner's manual (Additional Vol.) See owner's manual (Additional Vol.) See owner's manual of Memory viewer (optionally available) ●
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 63
    / Off On / Countdown off / Off Logo Logo select Capture Off Default User Yes / No Logo PIN code lock Logo PIN code entry Off On Logo PIN Lamp control On / Off Normal / Auto / Eco Pointer Spotlight / Pointer Quit Remote control Security Code 1 - Code 8 Key lock Off Projector Remote control
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 64
    Power management mode. 64 ✽ Either of the projector network, or memory viewer function is in abnormal condition. • • • green. • • • red • • • off • • • blinks green. • • • blinks red. ✽ When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 65
    Appendix Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with 800 x 600 53.674 85.06 SXGA 15 1280 x 1024 SVGA 5 800 x 600 48.08 72.19 SXGA 16 1280 x 1024 SVGA 6 800 x 600 37.90 61.03 SXGA 17 1152 x 900 SVGA 7 800 x 600
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 66
    Projection Image Size (Diagonal) Throw Distance Projection Lens Projection Lamp PLC-XU83 PLC-XU86 Adjustable from 40" to 300" 3.9' - 45.3' (1.2m - 13.8m) 3.3' - 38.7' (1.0m - 11.8m) F 1.65 ~ 1.81 lens with f 22.5 mm ~ 27 mm with manual zoom and focus 200W Interface Video Input Jack S-video
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 67
    Accessories Owner's Manual and Owner's Manual (Additional Vol.) AC Power Cord Remote Control and Batteries USB Cable DVI-VGA Cable Lens Cover with String PIN Code Label CD-ROM Soft Carrying Case USB Wireless LAN Adapter ● The specifications are subject to change without notice. ● LCD panels are
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 68
    Link password, see p49 on owner's manual (Additional Vol.) "Network Set-up and Operation". Projector Input Computer1 (Analog) Computer1 (Digital) RGB (PC digital) RGB (AV HDCP) RGB Computer2 Component RGB (Scart) Auto Video Video S-video Wired Wireless Memory Viewer PJLink Input RGB
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 69
    DVI-I TERMINAL (DIGITAL/ANALOG) C1 C2 12345678 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C3 C4 C5 C1 Analog Red Input + 5 ----- 2 TX - 6 RX - 3 RX + 7 ----- 4 ----- 8 ----- 87654321 SERVICE PORT CONNECTOR Terminal : Mini DIN 8-PIN 876 5 43 21 1 RXD 2 ----3 ----4 GND 5 RTS
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 70
    Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 71
  • Sanyo XU83 | Instruction Manual, PLC-XU83 - Page 72
    Printed in Japan Part No. 610 325 7877 (1AA6P1P4991-- MY5A) SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Multimedia Projector
MODEL
PLC-XU86
PLC-XU83
Owner’s Manual
Netw
or
k Suppor
t
ed
❏
Wireless LAN
IEEE802.11b/g
❏
Wired LAN
100-Base-TX/10-Base-T
Memory V
iew
er
❏
USB Memory Viewer
(optionally available)
Compatible with a dedicated USB memory
✽
Refer to the owner's manuals below for details about
network and memory viewer function.
■
Owner's Manual (Additional Vol.)
Network Set-up and Operation
■
Owner's Manual
USB Memory
This manual is provided with optionally supplied
USB memory.